| Author |
Message |
 Topic: F134 engine fuel pump question |
45auto
Replies: 14
Views: 2322
|
 Forum: Technical Knowledge Base Posted: Tue Jun 18, 2024 8:04 pm Subject: F134 engine fuel pump question |
| I followed your link to the fuel pump and I do not believe it is the correct / original fuel pump for your engine. I believe AC 4698 or 9562 would be the fuel pump you would want for the original loo ... |
| Topic: F134 engine fuel pump question |
45auto
Replies: 14
Views: 2322
|
Forum: Technical Knowledge Base Posted: Tue Jun 18, 2024 7:48 pm Subject: F134 engine fuel pump question |
| If you would like to keep an original theme with your rebuild, go with the correct fuel pump and rebuild it. If you should find an NOS fuel pumps they should be rebuilt as their diaphragms will not s ... |
| Topic: conversion from a 12 volt system back to a 24 volt system |
45auto
Replies: 7
Views: 1660
|
Forum: Technical Knowledge Base Posted: Mon Apr 01, 2024 7:48 pm Subject: conversion from a 12 volt system back to a 24 volt system |
| Depends on what all was removed to convert it to 12 Volts. While the major 24V items can be costly, the small items will be just as bad. I would advise taking inventory of what you have and what you ... |
| Topic: Speedometer Repair |
45auto
Replies: 20
Views: 4977
|
Forum: Technical Knowledge Base Posted: Mon Aug 28, 2023 12:16 pm Subject: Speedometer Repair |
You can give Bob's Speedometer a try. I know a couple of people who have use them and were happy with the results. However, they are not cheap!
https://www.bobsspeedometer.com/ |
| Topic: Is a Regulator VBC4004UT interchangeable with VBC4002UT |
45auto
Replies: 22
Views: 8384
|
Forum: Technical Knowledge Base Posted: Mon Apr 10, 2023 5:20 pm Subject: Is a Regulator VBC4004UT interchangeable with VBC4002UT |
Army Jeep Parts has the short ground straps for the 4 rubber mounts. A bit pricey if you need 4 of them................
https://www.armyjeepparts.com/p-4280-ground-strap-voltage-regulator-to-frame ... |
| Topic: Speedi Sleeve Recomendations |
45auto
Replies: 9
Views: 3779
|
Forum: Technical Knowledge Base Posted: Wed Jul 27, 2022 11:58 am Subject: Speedi Sleeve Recomendations |
| If you have a rather deep groove in your yolk, you will want to use Loctite 660 to fill in the groove which will keep the thin sleeve from being pressed down into the groove from the pressure from the ... |
| Topic: Carter YF 938 SD |
45auto
Replies: 6
Views: 3448
|
Forum: Technical Knowledge Base Posted: Fri Apr 22, 2022 10:06 am Subject: Carter YF 938 SD |
Here are some YF kit part numbers that may help you track down a rebuild kit.
Carquest 121A YF Rebuild Kit
High Grade 1611 YF Rebuild Kit --Made by Standard
NAPA 2-5096 YF Rebuild ... |
| Topic: 1952 M38A1 Is it a Navy Jeep or not? |
45auto
Replies: 10
Views: 4600
|
Forum: Technical Knowledge Base Posted: Wed Apr 20, 2022 6:48 pm Subject: 1952 M38A1 Is it a Navy Jeep or not? |
I can add to Wes comments.
Your engine serial number is most likely the factory original engine. Your engine serial number is in range with the others I have in my database. As Wes pointed out, the ... |
| Topic: M38 : OK, Boomer |
45auto
Replies: 300
Views: 96733
|
Forum: Jeep Project Threads Posted: Tue Mar 29, 2022 11:14 am Subject: M38 : OK, Boomer |
| I had the same problem with the longest head stud. Unless you are buying NOS hardware, the dealer's stock "off the shelf" hardware. The military uses lengths that are not industry standards. I'm not ... |
| Topic: M100 trailer on a trailer |
45auto
Replies: 15
Views: 10331
|
Forum: M100 & other 1/4 T trailers Posted: Sun Jan 02, 2022 5:20 pm Subject: M100 trailer on a trailer |
You have a very early Strick M100. It's only the third unit down on the serial number database I have on them.
Make Model Serial # DOD Military # Contract # Resp Agen Remarks
Strick Co. M 100 1 ... |
| Topic: New Wires For M38A1 |
45auto
Replies: 7
Views: 3935
|
Forum: Technical Knowledge Base Posted: Wed Dec 22, 2021 7:58 pm Subject: New Wires For M38A1 |
| Vintage Wiring is most likely making the harnesses you see for sale by others. Here is the link for the Wiring Harness for the M38A1. No prices but you can request a quote. I have talked to the owne ... |
| Topic: M38 Carter YS Carb |
45auto
Replies: 16
Views: 8617
|
Forum: Technical Knowledge Base Posted: Sun Oct 24, 2021 10:12 pm Subject: M38 Carter YS Carb |
| The pictures should help identify the carburetors. If any M38 carburetors are found with the original brass ID tag, I believe they are date coded and with a good sampling, we may come up with a workin ... |
| Topic: M38 Carter YS Carb |
45auto
Replies: 16
Views: 8617
|
Forum: Technical Knowledge Base Posted: Sat Oct 23, 2021 8:31 pm Subject: M38 Carter YS Carb |
It is an M38 carburetor---it is also the early first version carburetor.
http://willysmjeeps.com/v2/modules/gallery/albums/Harold-West/InkedEarly_M38_NOS_YS_637_Carburetor_3_Edited_2.sized.jpg
EAR ... |
| Topic: Distributor Weights |
45auto
Replies: 17
Views: 8789
|
Forum: Technical Knowledge Base Posted: Wed Sep 22, 2021 8:46 pm Subject: Distributor Weights |
| On the waterproof distributers, the "oiler" is low on the housing behind a brass slotted plug (you use a screwdriver to remove) inside there is a one inch long or so square felt that you would saturat ... |
| Topic: M38A1 Fording Video |
45auto
Replies: 3
Views: 3147
|
Forum: Technical Knowledge Base Posted: Thu Sep 02, 2021 10:03 am Subject: M38A1 Fording Video |
| It was cool however he was either brave or knew what the bottom was like and how deep it would be. Also, I would want a back up plan as just a little bit of water and in the wrong component and you wi ... |
| |
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
