Author |
Message |
Topic: 24volt Coils Again |
Cacti_Ken
Replies: 5
Views: 2347
|
Forum: Technical Knowledge Base Posted: Fri Oct 06, 2023 5:53 pm Subject: 24volt Coils Again |
Thanks Ron. I do feel embarrassed.
I wasn't measuring across the post.
The resistance is 12 ohms across the post of the one that I haven't put in the jeep yet to test.
The one I did install ran r ... |
Topic: 24volt Coils Again |
Cacti_Ken
Replies: 5
Views: 2347
|
Forum: Technical Knowledge Base Posted: Fri Oct 06, 2023 4:31 pm Subject: 24volt Coils Again |
Wes, I have come to the conclusion that I am probably not measuring in the correct places on the coil for the primary. I tried following one of your photos of the coil for the measuring of the prima ... |
Topic: 24volt Coils Again |
Cacti_Ken
Replies: 5
Views: 2347
|
Forum: Technical Knowledge Base Posted: Mon Oct 02, 2023 4:26 pm Subject: 24volt Coils Again |
Sorry it's taken me till now to reply.
I have an older model Fluke 8020B which has push buttons for the different modes and ranges. The 200 ohm range is the lowest range. A new 9v battery, I measur ... |
Topic: 24volt Coils Again |
Cacti_Ken
Replies: 5
Views: 2347
|
Forum: Technical Knowledge Base Posted: Fri Sep 22, 2023 7:50 pm Subject: 24volt Coils Again |
I recently ordered and received 2 coils. 24 volt coils that are assumed to be the best after market coils today.
After receiving the coils I did a resistance check on them.
The primary windings I f ... |
Topic: Installing a fuse in turn signal circuit |
Cacti_Ken
Replies: 14
Views: 9203
|
Forum: Technical Knowledge Base Posted: Sat Nov 23, 2019 9:44 pm Subject: Installing a fuse in turn signal circuit |
Thanks for the reply and comments Wes. I'm in the process of finding the appropriate diode. |
Topic: Installing a fuse in turn signal circuit |
Cacti_Ken
Replies: 14
Views: 9203
|
Forum: Technical Knowledge Base Posted: Fri Nov 22, 2019 8:31 pm Subject: Installing a fuse in turn signal circuit |
When I was restoring my M38 I installed the late style electronic turn signal controller.
Since then. I have ruined two controllers by accidently causing a short circuit of the 24 volts to ground eit ... |
Topic: Starter armature |
Cacti_Ken
Replies: 2
Views: 4337
|
Forum: Technical Knowledge Base Posted: Mon Jun 10, 2019 3:38 pm Subject: Starter armature |
Thanks Wes. |
Topic: Starter armature |
Cacti_Ken
Replies: 2
Views: 4337
|
Forum: Technical Knowledge Base Posted: Sun Jun 09, 2019 1:23 pm Subject: Starter armature |
I'm in the process of cleaning up a MCZ4001UT starter.
I've done a ohm reading check on the windings and checked for grounds. All appear to be good on that test. But I notice 5 places on the commu ... |
Topic: MP-65 antenna base and antenna sticks MS-116,117,118 |
Cacti_Ken
Replies: 7
Views: 11960
|
Forum: Technical Knowledge Base Posted: Wed Jun 22, 2016 9:47 pm Subject: MP-65 antenna base and antenna sticks MS-116,117,118 |
I doubt if I will ever buy any military radios. |
Topic: MP-65 antenna base and antenna sticks MS-116,117,118 |
Cacti_Ken
Replies: 7
Views: 11960
|
Forum: Technical Knowledge Base Posted: Tue Jun 21, 2016 10:53 am Subject: MP-65 antenna base and antenna sticks MS-116,117,118 |
Thank you both for the information. I have had the the antenna mounted to the M38 since restoration, but never acquired any military radios.
I don't know but I would imagine the transceiver had a ... |
Topic: MP-65 antenna base and antenna sticks MS-116,117,118 |
Cacti_Ken
Replies: 7
Views: 11960
|
Forum: Technical Knowledge Base Posted: Mon Jun 20, 2016 9:05 pm Subject: MP-65 antenna base and antenna sticks MS-116,117,118 |
What frequency range was this antenna use for? |
Topic: Fuel Pump rebulding |
Cacti_Ken
Replies: 17
Views: 26209
|
Forum: Technical Knowledge Base Posted: Sat Jun 06, 2015 6:46 am Subject: Fuel Pump rebulding |
It was late in the day when I received the photo of the kit and they were closed for the week end. I will have to call back Monday and ask about the diaphragms.
I was wondering if maybe some one he ... |
Topic: Fuel Pump rebulding |
Cacti_Ken
Replies: 17
Views: 26209
|
Forum: Technical Knowledge Base Posted: Fri Jun 05, 2015 1:43 pm Subject: Fuel Pump rebulding |
Then and now told me they didn't have info on these numbers 5592695 and 5592147.
I gave this number 1539917, and the lady I was talking with said it sounded more familiar. She gave me a price and fo ... |
Topic: Fuel Pump rebulding |
Cacti_Ken
Replies: 17
Views: 26209
|
Forum: Technical Knowledge Base Posted: Tue Jun 02, 2015 9:51 am Subject: Fuel Pump rebulding |
I didn't know if they would be any additional help, Since they have the same prefix as the numbers 5592659 and 5592147. |
Topic: Fuel Pump rebulding |
Cacti_Ken
Replies: 17
Views: 26209
|
Forum: Technical Knowledge Base Posted: Mon Jun 01, 2015 2:24 pm Subject: Fuel Pump rebulding |
I am surprised you were able to see all that from the box. Here is the close up of the box tag and the cover tag that was with it. Appreciate the help. I'm going to try my luck on rebuild and converti ... |
|