Search found 82 matches

Curious --- maybe I missed it (because you usually photograph everything) --- what did you use for anti-squeak material underneath the gas tank?
Seen here: http://willysmjeeps.com/v2/modules.php?name ...

Always a pleasure to see your work!
And great ingenuity custom bending a special wrench for fitting the fuel line elbow --- however --- that wouldn’t be necessary if the elbow was correctly located o ...

Fixing some rattles.

The rear seat has a rattle sound coming from the seats, after pulling back the cover you can see where the springs are wearing against the metal backing. If you slap the seat ...

Continued from above...

Dressing applied to the screw threads as well

https://photos.smugmug.com/M38/i-mGRtQ3d/0/LsdmxwjDrtcXdmBf69vHqj9ZvWTRFhPhcrMmqLVhb/X2/20250309_104240-X2.jpg

https:// ...

To quote Hannibal from the A-Team...."I love it when a plan comes together!" The M38 is running and driving again!

Today it's time to re-install the fuel tank and take the Jeep for a test drive ...

Continued from above...

New double lip seals ordered from Joe's Motor Pool

https://photos.smugmug.com/M38/i-bxqMRnQ/0/Lj5W4f4tRWNQ6h3RwhMSkZgtDjQ5xq8hRKx2phpGL/X2/20250307_091251-X2.jpg

https ...

Quest to reduce oil leaks...

The jeep leaks a small amount from each pinion seal so it's time to get some new seals installed.

Pulling the front yoke

https://photos.smugmug.com/M38/i-jLRSB7M/ ...

Thanks Tom.
I missed it because it's not where the TM says it should be (above the floor plate).

I wonder if that's a mistake in the manual? If the clamp was above the tin that would leave a gap w ...

Transmission boot has 2 clamps.
Maybe I missed it, but I see the smaller upper clamp (3/4") but not the larger lower clamp (2-3/4").

It's easy to miss as it blends in with the color of the boot, ...

https://shop.midwestmilitary.com/product/transmission-shift-boot-clamp/
Page 299 in the ORD9.

That's the clamp I installed. Thanks Ron

Tom

Vent line modification. When we purchased our M38 the vent line going from the trans/transfer case to the vacuum pump wasn't tied into the bell housing like it was suppose to be. With the floor pane ...

Thanks Wes. Sorry for the delay.

The power piston is out of a 1955 Ingersol Rand KVS Engine/Compressor. The engine is a single turbo natural gas fired V-6 unit that develops 1000hp at 330 rpm ...

That's odd? The M38 ORD 9 listing shows part number 143481 on page 32 which lists the fitting as "Tee, flared tube, inverted' brass, 1/4" tube, 3/16" tube, 1/8" male pipe side." Note the two female po ...

Well I'm held up a bit waiting for parts to arrive so lets tackle some smaller projects to keep the ball rolling.

When we purchased the Jeep the front shackles were bent outwards and they don't la ...

I believe the "T" (PN 143481 Pg 32 of ORD 9) actually has two female ends and the base leg end is male 1/8" pipe thread.

http://willysmjeeps.com/v2/modules/gallery/albums/album637/ventd.jpg
...


Create an account	Home · · Forums · · Articles · · Downloads · · Photo Gallery


PHP-Nuke Copyright © 2005 by Francisco Burzi. This is free software, and you may redistribute it under the GPL. PHP-Nuke comes with absolutely no warranty, for details, see the license.