| Author |
Message |
 Topic: M38 frame serial number tag? |
Kendall
Replies: 5
Views: 324
|
 Forum: Technical Knowledge Base Posted: Mon May 05, 2025 8:44 pm Subject: M38 frame serial number tag? |
Wes,
I think you meant to say that MB's had a frame tag, but M38's did not.
Kendall |
| Topic: Speaking of pilot M38s |
Kendall
Replies: 1
Views: 1227
|
Forum: Technical Knowledge Base Posted: Tue Sep 03, 2024 5:59 pm Subject: Speaking of pilot M38s |
| A previous forum poster mentioned the pilot/prototype M38s and consequently I was perusing some of my old MVCC Army Motors magazines and came across this ad from a 1987 ad from Army Jeep Parts Inc. li ... |
| Topic: Clutch release bearing support cast tab for return spring |
Kendall
Replies: 14
Views: 3049
|
Forum: Technical Knowledge Base Posted: Sat Mar 16, 2024 5:22 pm Subject: Clutch release bearing support cast tab for return spring |
The one on the left looks like the one RFJP sells-
https://www.rfjp.com/p-2398-clutch-throw-out-bearing-and-carrier-945255.aspx
Kendall, I looked Joe's parts up:
https://www.rfjp.com/images/p ... |
| Topic: USAF Forward Air Controller M38A1 photo |
Kendall
Replies: 3
Views: 1905
|
Forum: Announcements, News, Humor Posted: Fri Feb 23, 2024 3:55 pm Subject: USAF Forward Air Controller M38A1 photo |
| I recently came across this poster (it measures 15"X20") at a flea market and bought it. Original M38A1 US Air Force jeep. Notice how small the hood numbers are! It is a later M38A1 because it has ... |
| Topic: M38A1 fender |
Kendall
Replies: 2
Views: 2745
|
Forum: Wanted Posted: Fri Nov 24, 2023 5:57 pm Subject: M38A1 fender |
| Are you looking for early or late style? |
| Topic: m38 a 1 chassis paint |
Kendall
Replies: 9
Views: 3356
|
Forum: Technical Knowledge Base Posted: Tue Oct 17, 2023 7:15 pm Subject: m38 a 1 chassis paint |
Wes,
Ryan said the frame was OD but you are saying black. So since 19 years ago there is documentation that frames from the factory were black? |
| Topic: Need a couple of dimentions from a few folks |
Kendall
Replies: 17
Views: 7571
|
Forum: Technical Knowledge Base Posted: Sun Oct 08, 2023 2:56 pm Subject: Need a couple of dimentions from a few folks |
1951 M38= 46"
1952 M38= 46"
1952 M38A1=46" |
| Topic: Fuel gauge and sending unit match |
Kendall
Replies: 22
Views: 5472
|
Forum: Technical Knowledge Base Posted: Wed Oct 04, 2023 3:50 pm Subject: Fuel gauge and sending unit match |
| These are easy to test. Remove the sending unit from the tank and with power to it and it grounded, move the float up and down and watch the gauge move from full to empty if working properly. And yo ... |
| Topic: M-38 24 Volt charging system |
Kendall
Replies: 12
Views: 7478
|
Forum: Technical Knowledge Base Posted: Fri May 12, 2023 3:07 pm Subject: M-38 24 Volt charging system |
| If you decide to remove the cover of your regulator in place remember to disconnect the battery cable FIRST! |
| Topic: M416A1 trailer master cylinder |
Kendall
Replies: 4
Views: 3010
|
Forum: M100 & other 1/4 T trailers Posted: Fri Apr 21, 2023 2:02 pm Subject: M416A1 trailer master cylinder |
| It is just too weird that the text is identical with the same grammatical and spelling errors. |
| Topic: M416A1 trailer master cylinder |
Kendall
Replies: 4
Views: 3010
|
Forum: M100 & other 1/4 T trailers Posted: Fri Apr 21, 2023 1:26 pm Subject: M416A1 trailer master cylinder |
Is this the same person/question from years ago? Didn't you get your answer then?
http://www.willysmjeeps.com/v2/modules.php?name=Forums&file=viewtopic&t=4155&start=0&postdays=0& ... |
| Topic: M38 Crankshaft Pulley - Timing Marks |
Kendall
Replies: 33
Views: 9969
|
Forum: Technical Knowledge Base Posted: Thu Oct 13, 2022 9:37 am Subject: M38 Crankshaft Pulley - Timing Marks |
| Done |
| Topic: M38 Crankshaft Pulley - Timing Marks |
Kendall
Replies: 33
Views: 9969
|
Forum: Technical Knowledge Base Posted: Thu Oct 13, 2022 7:41 am Subject: M38 Crankshaft Pulley - Timing Marks |
Here is the article from the 1954 PS Magazine #18 page 837 for the pulley repair.
https://i.imgur.com/tV9wehKm.jpg |
| Topic: M38 Crankshaft Pulley - Timing Marks |
Kendall
Replies: 33
Views: 9969
|
Forum: Technical Knowledge Base Posted: Mon Oct 10, 2022 3:37 pm Subject: M38 Crankshaft Pulley - Timing Marks |
| The notches look to be the work of Bubba. |
| Topic: How to test coils? |
Kendall
Replies: 6
Views: 3379
|
Forum: Technical Knowledge Base Posted: Mon Oct 03, 2022 8:51 pm Subject: How to test coils? |
Try searching the web by using search terms such as "testing coil willysmjeeps" and you'll get several hits such as this one:
http://www.willysmjeeps.com/v2/modules.php?name=Forums&file=viewtopic ... |
| |
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
