| Author |
Message |
 Topic: Warn M3B locking hubs |
Texbillhs
Replies: 4
Views: 10595
|
 Forum: Technical Knowledge Base Posted: Fri May 13, 2016 8:30 am Subject: Warn M3B locking hubs |
Guessing from the CJ2A forum post the slotted washer and nut with set screws goes on top of the existing spindle bearing retainer nut.
http://www.thecj2apage.com/forums/warn-m3b-lock-o-matic-hubs ... |
| Topic: Warn M3B locking hubs |
Texbillhs
Replies: 4
Views: 10595
|
Forum: Technical Knowledge Base Posted: Fri May 13, 2016 5:58 am Subject: Warn M3B locking hubs |
| I see two parts (top left) - a slotted washer and a what looks look a nut that you'd install with a pin wrench. Those are separate from the rest of the assembly. I assume you remove the bolts on the ... |
| Topic: Warn M3B locking hubs |
Texbillhs
Replies: 4
Views: 10595
|
Forum: Technical Knowledge Base Posted: Thu May 12, 2016 7:15 pm Subject: Warn M3B locking hubs |
| Picked up a nice set of older Warn 10 spline locking hubs, M3B marked. I read they are automatic, work sort of like a ratchet. Is there installation instructions anywhere? I see no difference in th ... |
| Topic: Top side curtain rod hole measurement |
Texbillhs
Replies: 12
Views: 15652
|
Forum: Technical Knowledge Base Posted: Thu Oct 01, 2015 6:46 pm Subject: Top side curtain rod hole measurement |
| Did find a photo, it is a pocket, looks to be short maybe less than 2 inch. So I'll have to weld tabs to tubing then spot weld to the tub and tack the drilled hole. I likely won't get to it till aft ... |
| Topic: Top side curtain rod hole measurement |
Texbillhs
Replies: 12
Views: 15652
|
Forum: Technical Knowledge Base Posted: Thu Oct 01, 2015 6:21 pm Subject: Top side curtain rod hole measurement |
| The rods, 3/8 fit the tubing. I'm thinking I'll put a piece of rod in the tube as a stop and tack the tube to the drilled hole and to the hat channel. It's not an award-winning 38 - it's a lot of sa ... |
| Topic: Top side curtain rod hole measurement |
Texbillhs
Replies: 12
Views: 15652
|
Forum: Technical Knowledge Base Posted: Thu Oct 01, 2015 5:41 pm Subject: Top side curtain rod hole measurement |
| Brett does the u excustion piece extend to the hat channel angled piece? In my case tube. |
| Topic: Top side curtain rod hole measurement |
Texbillhs
Replies: 12
Views: 15652
|
Forum: Technical Knowledge Base Posted: Wed Sep 30, 2015 6:06 pm Subject: Top side curtain rod hole measurement |
| It's a repro tub that didn't have the holes. I will be welding in tubes (pockets) - I was figuring on using 30- 1/2. There's nothing much to the rods 3/8 rod. There's those measurements somewhere o ... |
| Topic: Top side curtain rod hole measurement |
Texbillhs
Replies: 12
Views: 15652
|
Forum: Technical Knowledge Base Posted: Wed Sep 30, 2015 2:18 pm Subject: Top side curtain rod hole measurement |
| Error, that's 3/4" that seems like a large amount |
| Topic: Top side curtain rod hole measurement |
Texbillhs
Replies: 12
Views: 15652
|
Forum: Technical Knowledge Base Posted: Wed Sep 30, 2015 2:05 pm Subject: Top side curtain rod hole measurement |
| 3/8" difference , I guess they weren't concerned with accuracy that much. That's that's what I needed. |
| Topic: Top side curtain rod hole measurement |
Texbillhs
Replies: 12
Views: 15652
|
Forum: Technical Knowledge Base Posted: Wed Sep 30, 2015 9:26 am Subject: Top side curtain rod hole measurement |
| If someone has a M38 with the original tub handy I need the measurement from the dash to the center of the side curtain rod hole. |
| Topic: patterns for M38 rear seat canvas |
Texbillhs
Replies: 4
Views: 7313
|
Forum: Technical Knowledge Base Posted: Fri May 15, 2015 4:16 pm Subject: patterns for M38 rear seat canvas |
| Kendall, I sent a pm |
| Topic: patterns for M38 rear seat canvas |
Texbillhs
Replies: 4
Views: 7313
|
Forum: Technical Knowledge Base Posted: Fri May 15, 2015 7:14 am Subject: patterns for M38 rear seat canvas |
| Taking it there isn't any patterns here |
| Topic: M38 left side (driver's) door skin |
Texbillhs
Replies: 0
Views: 4481
|
Forum: Wanted Posted: Thu May 14, 2015 7:05 pm Subject: M38 left side (driver's) door skin |
| Would like to fine a NOS or decent shape M38 left side (driver's) door skin |
| Topic: patterns for M38 rear seat canvas |
Texbillhs
Replies: 4
Views: 7313
|
Forum: Technical Knowledge Base Posted: Thu May 14, 2015 6:59 pm Subject: patterns for M38 rear seat canvas |
| I found canvas material today. I have the seat frame, bottom and back springs and padding. Is there a How To Do canvas pattern somewhere in the member photo albums? I wouldn't be surprised if there ... |
| Topic: Discounted Carburetor |
Texbillhs
Replies: 9
Views: 15522
|
Forum: Technical Knowledge Base Posted: Sun May 03, 2015 6:34 pm Subject: Discounted Carburetor |
| If you mean a Solex I found 1st the fuel pressure is very important, I used an electric pump but you can use a regulator. Then on mine we had to sweak the high speed - I'm told most work right out of ... |
| |
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
