Create an account	Home  ·  ·  Forums  ·  ·  Articles  ·  ·  Downloads  ·  ·  Photo Gallery

Login Nickname Password Don't have an account yet? You can create one here. Navigation · Home · Article Archive · Article Submit · Downloads · FAQ · Forums · Members List · Photo Gallery · Private Messages · Web Links · Your Account Search Articles Forums McArthur Deep Water kit. M38 vs M38A1 Top bows wanted Full set of radios - $1,250.00 USD will package for shipping M38A1 Front to rear floor riser measurement M38 transfer case yoke torque NOS m-38 UNDER GAS TANK anti-squeak in original box can't add photos adding photos Need a PE-103-A dynomotor / generator? Willys M Jeeps Forums

Forum FAQ   Search   Usergroups   Profile   Log in to check your private messages   Log in  Search found 45 matches willysmjeeps.com Forum Index Author Message   Topic: 1952 M-38 Temp. Sending unit jerry72 Replies: 8 Views: 14054 Forum: Technical Knowledge Base   Posted: Mon Dec 29, 2014 2:15 pm   Subject: 1952 M-38 Temp. Sending unit Thanks for the feedback guys. I'll try my luck with a repo unit and see how that goes. Jerry   Topic: 1952 M-38 Temp. Sending unit jerry72 Replies: 8 Views: 14054 Forum: Technical Knowledge Base   Posted: Sun Dec 28, 2014 11:43 am   Subject: 1952 M-38 Temp. Sending unit Thank you for your response Brian. Sending unit screws in the block so grounding should be fine. When I measure the ohms on the sending unit I ground one lead to the engine block. That's when the n ...   Topic: 1952 M-38 Temp. Sending unit jerry72 Replies: 8 Views: 14054 Forum: Technical Knowledge Base   Posted: Sun Dec 28, 2014 7:28 am   Subject: 1952 M-38 Temp. Sending unit Hi guys, Had to replace my temp. sending unit ac-7389566 with NOS ac-1512245. Gage= ac-1512422. Gage reads 0 with new sending unit with engine hot. Checked sending unit resistance according ...   Topic: M-38 Paint jerry72 Replies: 3 Views: 7021 Forum: Technical Knowledge Base   Posted: Tue Nov 25, 2014 5:09 am   Subject: M-38 Paint Thank you gentlemen for the info and advice. Jerry   Topic: M-38 Paint jerry72 Replies: 3 Views: 7021 Forum: Technical Knowledge Base   Posted: Mon Nov 24, 2014 9:42 am   Subject: M-38 Paint Approximately how much paint will I have to purchase to paint a M-38 (inside and out)?   Topic: M38 History jerry72 Replies: 2 Views: 6413 Forum: Technical Knowledge Base   Posted: Sun Nov 16, 2014 12:26 pm   Subject: M38 History Thanks Wes for your response.   Topic: M38 History jerry72 Replies: 2 Views: 6413 Forum: Technical Knowledge Base   Posted: Sun Nov 16, 2014 7:58 am   Subject: M38 History Is there a data base I can search to find the history of my 1952 M-38 (MC 64434 Willys Overland Data plate) Jeep?   Topic: Distributor plumbing jerry72 Replies: 4 Views: 7191 Forum: Technical Knowledge Base   Posted: Tue Jun 19, 2012 6:41 am   Subject: Distributor plumbing Looking to purchase distr. plumbing for 52 m38, any ideas? Jerry   Topic: Excesive toe in jerry72 Replies: 7 Views: 11849 Forum: Technical Knowledge Base   Posted: Thu Mar 22, 2012 8:45 pm   Subject: Excesive toe in John, I did check the toe in and the left tire is 1/8'' right is 2 1/2" But the jeep pulls to the right. Should be pulling left with 2 1/2" toe in on the right. There is a little play in the ste ...   Topic: Excesive toe in jerry72 Replies: 7 Views: 11849 Forum: Technical Knowledge Base   Posted: Tue Mar 20, 2012 6:38 am   Subject: Excesive toe in Ok then my problem should be loose bearing because the jeep pulls to the right. I'll check it. Thanks Wes for your help. God Bless Jerry   Topic: Excesive toe in jerry72 Replies: 7 Views: 11849 Forum: Technical Knowledge Base   Posted: Mon Mar 19, 2012 8:11 pm   Subject: Excesive toe in What could be the cause of excesive toe in on the right side tire (2 1/2 inch). Left is about 1/8 in. There is no damage to the tie rod. The jeep wants to turn right when I let the steering wheel ...   Topic: M38 idle jerry72 Replies: 16 Views: 21188 Forum: Technical Knowledge Base   Posted: Wed Feb 29, 2012 6:06 pm   Subject: M38 idle I'm still having idle issues when the engine is hot. No backfire just dies. I installed rebuilt fuel pump(then & now), carter ys carb(debellas), new coil, condenser, rotor, points(.020)(Debellas). ...   Topic: M38 starting issues jerry72 Replies: 9 Views: 13386 Forum: Technical Knowledge Base   Posted: Wed Feb 15, 2012 11:18 am   Subject: M38 starting issues Used grease for the shaft and 3 in one for the felt. Gaped points .020, new rotor, condensor, points. Starts just fine now. Thank you Jesus On to the next problem Jerry   Topic: M38 starting issues jerry72 Replies: 9 Views: 13386 Forum: Technical Knowledge Base   Posted: Sat Feb 11, 2012 1:07 pm   Subject: M38 starting issues Could I use grease? Once again thank you for your expertise Wes. Jerry   Topic: M38 starting issues jerry72 Replies: 9 Views: 13386 Forum: Technical Knowledge Base   Posted: Sat Feb 11, 2012 6:37 am   Subject: M38 starting issues Engine started to turn off when hot. started to hard crank again. Checked ignition coil and sure enough it was leaking oil. Ordered new coil, points, condenser, rotor from Debellas. once installed th ...   Page 1 of 3 Goto page 1, 2, 3  Next All times are GMT - 6 Hours Jump to: Select a forum Jeeps----------------Technical Knowledge BaseJeep Project ThreadsFor SaleWantedAuctionsM100 & other 1/4 T trailersEvents/TransportationAnnouncements, News, HumorM Series Parts Supply & Service ReviewPhoto Posting & Gallery requests/problems Other----------------This Web Site  Powered by phpBB © 2001 phpBB Group Forums ©

PHP-Nuke Copyright © 2005 by Francisco Burzi. This is free software, and you may redistribute it under the GPL. PHP-Nuke comes with absolutely no warranty, for details, see the license.