| Author |
Message |
 Topic: T90 felt seals |
randy
Replies: 1
Views: 3773
|
 Forum: Technical Knowledge Base Posted: Fri Aug 05, 2011 6:38 pm Subject: T90 felt seals |
| Rebuilding the T90. My old T90's [2] don't have the felt seal for the output shafts. The rebuild kit gives me two. I guess this was an improvement and I should install them? [between the yoke and rubb ... |
| Topic: Prop Shaft seals |
randy
Replies: 4
Views: 4888
|
Forum: Technical Knowledge Base Posted: Sun Apr 24, 2011 10:05 am Subject: Prop Shaft seals |
| Walcks4wd.com has it I think. It is called Felt Seal Yoke Sleeve Drive Shaft. |
| Topic: Omnix repair panel |
randy
Replies: 2
Views: 3898
|
Forum: Technical Knowledge Base Posted: Tue Aug 03, 2010 11:12 am Subject: Omnix repair panel |
I need to replace the under door forward passenger side panel [has the ax and shovel detents]. wondering about quality and fit of the Omnix repop.
Thanks |
| Topic: Transmission Hump Needed |
randy
Replies: 13
Views: 13723
|
Forum: Wanted Posted: Sun Jul 18, 2010 12:36 pm Subject: Transmission Hump Needed |
Try not to laugh.
http://img.mypicgallery.com/cheesey123/cheesey2_large.jpg |
| Topic: Transmission Hump Needed |
randy
Replies: 13
Views: 13723
|
Forum: Wanted Posted: Sun Jul 18, 2010 12:30 pm Subject: Transmission Hump Needed |
| The portion under the tool box is the worst.What is left is very thin. Just looking for an easy way out. I can live with everything else.Floor pans and complete hat channels from MWM are top notch. I ... |
| Topic: Transmission Hump Needed |
randy
Replies: 13
Views: 13723
|
Forum: Wanted Posted: Sat Jul 17, 2010 4:48 pm Subject: Transmission Hump Needed |
| Thanks Wes. I wasn't clear enough. It's not any of the bolt ons.I'm looking the portion with the the PTO hole rearward. So it is actually the center portion of the main floor pan. I realize this will ... |
| Topic: Transmission Hump Needed |
randy
Replies: 13
Views: 13723
|
Forum: Wanted Posted: Sat Jul 17, 2010 10:28 am Subject: Transmission Hump Needed |
| It is a M38 I am working on. |
| Topic: Transmission Hump Needed |
randy
Replies: 13
Views: 13723
|
Forum: Wanted Posted: Sat Jul 17, 2010 10:23 am Subject: Transmission Hump Needed |
I sand blasted my tub and the tranny hump is pretty bad. Anyone out there parting out a tub? Or any sugestions.
Thanks in advance. |
| Topic: MG Mount M31A1 on M38 |
randy
Replies: 1
Views: 4570
|
Forum: Technical Knowledge Base Posted: Sun May 23, 2010 8:20 am Subject: MG Mount M31A1 on M38 |
Hi, can anyone provide a dimensional drawing for the under floor bracing for mounting the M31A1 MG Mount to the M38?
Thanks
Randy |
| Topic: Fuel Pickup Unit |
randy
Replies: 1
Views: 3645
|
Forum: Technical Knowledge Base Posted: Fri Aug 29, 2008 9:42 am Subject: Fuel Pickup Unit |
| I have a fuel pickup unit for an A1. Can I use this on my M38 by shimming it up and reducing the fuel outlet to 1/4 inch? |
| |
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
