| View previous topic :: View next topic |
| Author |
Message |
Ryan_Miller
Site Administrator
Joined: Apr 03, 2005
Posts: 1652
Location: Kansas
|
 Posted: Fri Nov 07, 2008 8:39 pm Post subject: M-Series Wiring Harness |
 |
|
Subject: M-Series Wiring Harness
Status: Reproduction
Sold By: Made by Vintage Wiring of Maine
Review:
Shape/Appearance:
The wiring harness I bought was the correct douglas connectors and the proper lengths. They also make harnesses with Packard connectors and can make harnesses for other civilian and military vehicles.
The only appearance issue was that the wiring had printed on it "Prestolite", which did not buy out Auto-Lite until 1961, but the lettering is small and not extremely noticable.
Fit/Function:
Fit and works well. You may need to slightly grease the connector rubber because they can be hard to snap the shells together (as they were when new).
Summary:
Overall a good product. Be sure to specify what circuit breaker set up you have on your vehicle and if you want to add turn signals, etc to your harness.
Rating: 9.5 (1- 10, 10 highest)
_________________
Ryan Miller
MVPA # 22010 |
|
| Back to top |
|
 |
Cacti_Ken
Member
Joined: Apr 20, 2005
Posts: 1021
Location: Silsbee, Texas
|
| Posted: Fri Nov 07, 2008 10:47 pm Post subject: |
|
|
Ryan, what type of grease did you use on the components.
_________________
Tropical Veteran
35th Inf. Reg. "CACTI" 4th I.D. VN
Amateur Radio K5XOM |
|
| Back to top |
|
|
Ryan_Miller
Site Administrator
Joined: Apr 03, 2005
Posts: 1652
Location: Kansas
|
| Posted: Sat Nov 08, 2008 3:57 pm Post subject: |
|
|
Ken,
I have not put any on yet, but I read in PS Magazine from 1959 no 77, that they recomended some to help get the connecting shells together. They stated that they needed to be firm to hold the water out.
Insulating compuond, electrical paste (Spec MIL-I-8660)
FSN 5970-224-5277... 2 OZ tube up to 50 lb can (5970-242-0910)
It does not harden or evaporate and will not hurt the rubber connectors.
I have yet to research this compound further, but I have found it can be difficult to squeeze the metal shells to lock due to the rubber.
_________________
Ryan Miller
MVPA # 22010 |
|
| Back to top |
|
|
Cacti_Ken
Member
Joined: Apr 20, 2005
Posts: 1021
Location: Silsbee, Texas
|
| Posted: Sat Nov 08, 2008 6:32 pm Post subject: |
|
|
Ryan I used silicone grease. It is not suppose to harm the rubber.
_________________
Tropical Veteran
35th Inf. Reg. "CACTI" 4th I.D. VN
Amateur Radio K5XOM |
|
| Back to top |
|
|
Ryan_Miller
Site Administrator
Joined: Apr 03, 2005
Posts: 1652
Location: Kansas
|
| Posted: Sat Nov 08, 2008 8:24 pm Post subject: |
|
|
That sounds good to me.
_________________
Ryan Miller
MVPA # 22010 |
|
| Back to top |
|
|
wesk
Site Administrator
Joined: Apr 04, 2005
Posts: 16365
Location: Wisconsin
|
|
| Back to top |
|
|
oilleaker1
Member
Joined: May 14, 2009
Posts: 972
Location: South Dakota
|
| Posted: Sun Aug 22, 2010 11:20 am Post subject: |
|
|
Vintage wiring of Maine recommended filing the end of the plastic connector to shorten it some which helps, but after 3 harnesses, I found that if you remove or delete one of the cupped washers that go against the rubbers, you can install them a heck of alot easier. Steel washer, steel cap, I didn't see any harm in removing a washer. I don't plan on EVER putting my rigs under water. I keep them clean and dry after use. This is for the Douglas-Type connectors! Packard-Type , silicone grease really helps. My 2 cents,  John |
|
| Back to top |
|
|
Ryan_Miller
Site Administrator
Joined: Apr 03, 2005
Posts: 1652
Location: Kansas
|
| Posted: Thu Aug 26, 2010 10:18 am Post subject: |
|
|
John,
I ended up using a little of the electrical grease and sanding the ends of the plastic connectors down a little.
They can be really hard to fit together, but like you I don't plan on running under water. 
_________________
Ryan Miller
MVPA # 22010 |
|
| Back to top |
|
|
|
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
