View previous topic :: View next topic |
Author |
Message |
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16289 Location: Wisconsin
|
|
Back to top |
|
|
Bill_F Member
Joined: Apr 17, 2005 Posts: 891 Location: New Hampshire
|
Posted: Wed Apr 07, 2010 4:28 am Post subject: |
|
|
I did try him he says he has the parts but I need to give him measurements of my old parts, which for the bearing is next to impossible. since they are both blown apart. |
|
Back to top |
|
|
gianjeep Member
Joined: Mar 03, 2009 Posts: 35 Location: italy
|
Posted: Mon Apr 12, 2010 12:56 am Post subject: ramsey |
|
|
hello jeep people
for ramsey winch i've found nice information in merl's garage web site,chek it out |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16289 Location: Wisconsin
|
|
Back to top |
|
|
Rod Member
Joined: Apr 19, 2005 Posts: 15 Location: Heart of Dixie
|
Posted: Fri Apr 16, 2010 7:19 pm Post subject: |
|
|
wesk wrote: | ....Bill, You might also send Rod an email to see where he got his nice shiney bearing support. |
My hanger bearing is an original which came with my 50R winch. Before I mounted my winch setup on my M38. I cleaned up the brass hanger bearing with the wire wheel and sprayed it with clear spraypaint to keep the brass looking new. |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16289 Location: Wisconsin
|
|
Back to top |
|
|
Bill_F Member
Joined: Apr 17, 2005 Posts: 891 Location: New Hampshire
|
Posted: Wed Apr 21, 2010 8:04 am Post subject: |
|
|
Does anyone have a drawing of the winch mounting frame, I would like to see about having one made. |
|
Back to top |
|
|
Bill_F Member
Joined: Apr 17, 2005 Posts: 891 Location: New Hampshire
|
Posted: Fri Apr 23, 2010 7:32 am Post subject: |
|
|
Ok looking at my winch, not only does the data plate say 5000lbs instead of 3500lbs but from pictures of other winches I have seen the plate is on the wrong side of the housing. The plate is on the input side of the winch, facing the grill. There are no holes where a plate would have been in the front of the winch. Anyone have any ideas? I always seem to end up with the old ball parts/jeep |
|
Back to top |
|
|
Bill_F Member
Joined: Apr 17, 2005 Posts: 891 Location: New Hampshire
|
Posted: Mon May 10, 2010 1:06 pm Post subject: |
|
|
Ok all the U-joints from the civvy pto winches I have/had are junk, where can I get u-joints for the winch? Anyone have a part number? I dont care if they are correct, they just need to work. |
|
Back to top |
|
|
Bill_F Member
Joined: Apr 17, 2005 Posts: 891 Location: New Hampshire
|
Posted: Wed May 12, 2010 5:05 am Post subject: |
|
|
The resto of the winch continues, got all the parts back from the machine shop and they look and fit great. I have been cleaning the case as well. Today I am going to try to find a seal for it at napa. I have ordered just about everything else I need from ramsey. |
|
Back to top |
|
|
Bill_F Member
Joined: Apr 17, 2005 Posts: 891 Location: New Hampshire
|
Posted: Sun May 16, 2010 1:58 pm Post subject: |
|
|
The winch is coming along nicely. I have some of it back together. I am just waiting for my new seals and bearings from ramsey, and a seal I ordered from a local parts store. I will then have the new bearings pressed in. This poor winch has seen a hard life. Some of the holes for the bolts that for the mount needed some work but I have it all fixed now. Hopefully next weekend the winch itself will be back together. I am just waiting for the mount so I can put it in my jeep. I will take pics when I have it all back together. |
|
Back to top |
|
|
Bill_F Member
Joined: Apr 17, 2005 Posts: 891 Location: New Hampshire
|
Posted: Thu May 20, 2010 7:56 pm Post subject: |
|
|
I have the winch all back together now. Just waiting on the mount so I can put it in the jeep. This poor winch was pretty tired but now looks good. Never mind the mess in the back ground.
|
|
Back to top |
|
|
Bill_F Member
Joined: Apr 17, 2005 Posts: 891 Location: New Hampshire
|
Posted: Thu Jun 17, 2010 3:45 pm Post subject: |
|
|
I installed the winch on the jeep today. My poor winch had a hard life, the drum is a little miss-shaped and someone at some point had drilled and tapped some for mounting holes to 7/16, so it was a bit of a bear to mount. However it is now one the jeep. Waiting to get the pto, hanger bearing, and drive shafts.
|
|
Back to top |
|
|
Bill_F Member
Joined: Apr 17, 2005 Posts: 891 Location: New Hampshire
|
Posted: Wed Nov 03, 2010 6:55 pm Post subject: |
|
|
Getting closer on my complete winch set up. I received a Ramsey 105 pto today. I also have a line on a 2nd one, so I might have one for sale when I receive the other one.
|
|
Back to top |
|
|
SteveJ Member
Joined: Jun 14, 2005 Posts: 110 Location: Calgary Alberta
|
Posted: Wed Nov 10, 2010 7:52 pm Post subject: |
|
|
Kind of nice when it all starts to come together. _________________ SteveJ
1986 CDN Armstron MT500 dispatch Motorcycle
1986 arrow 1.75 t cargo trailer
1991 Reynolds Boughton RB44 GS TUH
1952 M38 CDN W/W (Sold)
1953 M100 CDN Trailer
1951 PE95K Genset (Sold) |
|
Back to top |
|
|
|