View previous topic :: View next topic |
Author |
Message |
OKCM38CDN Guest
![](modules/Forums/images/avatars/gallery/blank.gif)
|
Posted: Tue May 16, 2006 5:36 pm Post subject: Drag Link / Bell Crank Repair... |
|
|
I purchased a Drag Link kit today and am thinking that I should rebuild the Bell crank also... (the drag link canvas/cover on the fron won't stay in place) Thoughts...
At higher speeds I have a bit of play in the steering, not a lot but enough that if you are not paying attention you might wander...
Thanks in advance... |
|
Back to top |
|
![](modules/Forums/templates/willysmjeeps/images/spacer.gif) |
Bob_C Site Administrator
![Site Administrator Site Administrator](modules/Forums/willysmjeeps_rank/Admin_rank.gif)
![](modules/Forums/images/avatars/gallery/blank.gif)
Joined: Apr 03, 2005 Posts: 271 Location: Chester County, PA
|
Posted: Tue May 16, 2006 6:18 pm Post subject: |
|
|
Hey Hal,
The rubber cover + plate on the M38A1's draglink is the same darn way. Wont stay in place. Poor design if you ask me. I wire tied mine to the draglink, seems to work well. _________________ Bob Collins
1954 M38A1 MD79056 |
|
Back to top |
|
![](modules/Forums/templates/willysmjeeps/images/spacer.gif) |
wesk Site Administrator
![Site Administrator Site Administrator](modules/Forums/willysmjeeps_rank/Admin_rank.gif)
![](modules/Forums/images/avatars/gallery/003.gif)
Joined: Apr 04, 2005 Posts: 16286 Location: Wisconsin
|
|
Back to top |
|
![](modules/Forums/templates/willysmjeeps/images/spacer.gif) |
OKCM38CDN Guest
![](modules/Forums/images/avatars/gallery/blank.gif)
|
Posted: Thu May 18, 2006 5:38 pm Post subject: |
|
|
Well, I spent last evening (about 6 hrs) and got the drag link and bell crank replaced... boy what a job... Incorrect tools and lack of experience...
The drag link springs and bushings were fairly well worn, and the bell crank bearings had some grease in them but were dry... So all is back together and I will grease evrything up in the morning (Day off) and give it a test drive...
I can see where a press is help full in the shop had to improvise getting the bearings out and in again, also a tie rod fork is in order...
Thanks for the replies... |
|
Back to top |
|
![](modules/Forums/templates/willysmjeeps/images/spacer.gif) |
Ryan_Miller Site Administrator
![Site Administrator Site Administrator](modules/Forums/willysmjeeps_rank/Admin_rank.gif)
![](http://www.surfacezero.com/g503/data/821/flag.gif)
Joined: Apr 03, 2005 Posts: 1635 Location: Kansas
|
Posted: Fri May 19, 2006 10:58 am Post subject: |
|
|
Hal,
Let us know how your first test drive goes on the new steering stuff.
I am replacing all of mine with new stuff as I go, so I am hoping to avoid going back in.
Good Luck!
PS: thanks for the vent tubing! ![Cool](modules/Forums/images/smiles/icon_cool.gif) _________________ Ryan Miller
MVPA # 22010 |
|
Back to top |
|
![](modules/Forums/templates/willysmjeeps/images/spacer.gif) |
Ryan Member
![](modules/Forums/images/avatars/gallery/blank.gif)
Joined: Jan 10, 2006 Posts: 136 Location: Russellville, AR
|
Posted: Fri May 19, 2006 11:10 am Post subject: |
|
|
When tightening the drag link springs up, how tight should they be? |
|
Back to top |
|
![](modules/Forums/templates/willysmjeeps/images/spacer.gif) |
PeteL Member
![](modules/Forums/images/avatars/gallery/blank.gif)
Joined: Apr 07, 2006 Posts: 36
|
Posted: Fri May 19, 2006 11:25 am Post subject: |
|
|
Tighten up the big screw/plug at each end, then back them off a little bit, about one-quarter to one-half a turn, until you can align the cotter pins.
I think the bell crank end is supposed to be about a half-turn, the pitman end is one-quarter. Someone better informed may be able to confirm the exact specification.
Good luck.
Pete[/i][/list] |
|
Back to top |
|
![](modules/Forums/templates/willysmjeeps/images/spacer.gif) |
OKCM38CDN Guest
![](modules/Forums/images/avatars/gallery/blank.gif)
|
Posted: Fri May 19, 2006 1:32 pm Post subject: |
|
|
Test drive went great, a lot of play was taken out of the system, and it is easier to steer (less wandering as I call it)...
I tightened the drag link as enough to get the cotter pins in... There was not a lot of extra in mine... as it was I had to force the balls on the end of the pitman arm and bell crank into the drag link cause the springs were so tight... everything tightened up to where they should be and works fine...
I lubed it up this morning and away I went...
Fixing a wandering piece of foam in the seat and will be ready for the parade in the morning...
Thanks all for the replies...
Ryan, no problem, have materials for more should anyone need them... |
|
Back to top |
|
![](modules/Forums/templates/willysmjeeps/images/spacer.gif) |
PeteL Member
![](modules/Forums/images/avatars/gallery/blank.gif)
Joined: Apr 07, 2006 Posts: 36
|
Posted: Fri May 19, 2006 4:04 pm Post subject: |
|
|
Hal,
I hope you tighened those screw plugs all the way down to make solid contact, then backed them out just a hair. The ball ends need to be mechanically "locked in" the socket, not just under spring pressure, as I recall it.
It's been a long time since I did one, can anyone else confirm this?
I believe the springs are meant to be almost fully compressed and only take out the tiny bit of residual play. The 'socket' and screw plug do the real work.
Don't want that drag link popping off when you hit a bump on the highway!
Just checking...
Pete |
|
Back to top |
|
![](modules/Forums/templates/willysmjeeps/images/spacer.gif) |
OKCM38CDN Guest
![](modules/Forums/images/avatars/gallery/blank.gif)
|
Posted: Fri May 19, 2006 6:31 pm Post subject: |
|
|
By the time I got them Tightened up, the screw ends would not go any further, the new parts were longer than the old ones were due to wear...
I paid close attention to that detail, the drag link falling out would be a bad thing... ![Very Happy](modules/Forums/images/smiles/icon_biggrin.gif) |
|
Back to top |
|
![](modules/Forums/templates/willysmjeeps/images/spacer.gif) |
|