View previous topic :: View next topic |
Author |
Message |
Bobber Member
Joined: Feb 09, 2014 Posts: 178 Location: Tri Cities, Washington
|
Posted: Tue Jan 19, 2016 2:00 pm Post subject: Checking fuel pressure |
|
|
Working on 52 M38 with all stock original parts or rebuild kits from Midwest Military. What kind of pressure Gage would I use to check my fuel pump? I think I'm getting too much pressure to my YS 637 carter. I know I need to tee in right before the carb, but I'm unsure of what type or kind of Gage. Or the needle and seat valve are not stopping the fuel. It floods out real quick, I have pipe plugs in place of priming nozzles. So I can pull the plugs and blow compressed air into the intake and evacuate any fuel build up. Then she starts up right away. I get about a half a cup out when I do this. I'm still in the investigating mode right now.
Thanks. Rusty |
|
Back to top |
|
|
RICKG Member
Joined: Aug 31, 2010 Posts: 1744 Location: SO IDAHO
|
Posted: Tue Jan 19, 2016 4:12 pm Post subject: |
|
|
A typical eng vac/fuel pump tester. _________________ keep 'em rollin'
RICKG MC 51986 DOD 01-52, '50 CJ3a |
|
Back to top |
|
|
Bobber Member
Joined: Feb 09, 2014 Posts: 178 Location: Tri Cities, Washington
|
Posted: Tue Jan 19, 2016 6:29 pm Post subject: |
|
|
Thank you. |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16365 Location: Wisconsin
|
Posted: Tue Jan 19, 2016 9:33 pm Post subject: |
|
|
Bobber,
Keep an open mind when troubleshooting. Cracks in the carb's bowl can allow raw gas to flood the manifold. High fuel pump pressure can allow the carb inlet needle to be forced open. A stuck heat riser valve on an M38 can cause perculation of the fuel in the bowl pushing it into the venturi. Float height setting too high can cause the flooding as well. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
Bobber Member
Joined: Feb 09, 2014 Posts: 178 Location: Tri Cities, Washington
|
Posted: Wed Jan 20, 2016 12:38 am Post subject: |
|
|
Thank you, good to know. I've been chasing ghost trying to find my problem. With the process of elimination, I've ruled out the distributor and or timing components. It runs well, but just not for long. I will keep these things in mind. I need some info for when I ask questions in the future. Sometimes I'm not sure which questions I'm to ask
Thanks |
|
Back to top |
|
|
scoutpilot Member
Joined: Aug 31, 2015 Posts: 29 Location: Asheboro, NC
|
Posted: Wed Jan 20, 2016 3:57 am Post subject: |
|
|
Is there a spacer between the pump and block? _________________ Old fashioned service never goes out of style. |
|
Back to top |
|
|
Bobber Member
Joined: Feb 09, 2014 Posts: 178 Location: Tri Cities, Washington
|
Posted: Wed Jan 20, 2016 10:39 am Post subject: |
|
|
Yes. I put everything back to close to original as possible.
Thank you. |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16365 Location: Wisconsin
|
|
Back to top |
|
|
|