View previous topic :: View next topic |
Author |
Message |
Brumbach Member
Joined: Jun 18, 2013 Posts: 178
|
Posted: Fri Mar 25, 2016 7:20 am Post subject: L-134 stuck valves |
|
|
Approximately 40 years ago, I "barned" my M38. It was running at the time with no issues. Well, it's out of the barn now and I'm beginning a full restoration. I wished I'd taken the time to condition things before storing, such as pickling the engine. Oh well... The majority of valves are stuck. The rotating assembly rotates easily until the cam lobes encounter the stuck valve(s). Most of the valves are frozen in the closed position. A couple in the open position. Two valves are free. Aside from treating with heat and penetrating oil, can you think of other ways to free up the stuck valves?
Thanks in advance,
Bill |
|
Back to top |
|
|
4x4M38 Member
Joined: May 30, 2014 Posts: 3459 Location: Texas Hill Country
|
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16355 Location: Wisconsin
|
Posted: Fri Mar 25, 2016 8:15 am Post subject: |
|
|
Most cases it's dry guides and rusty or lead coated stems. What needs to be done next depends on your definition of "beginning a full restoration"
In most full restorations the engine gets restored along with the jeep.
If this is the case then pull the engine disassemble it for overhaul. Use a brass punch to knock the offended valves loose after the cam is removed.
In this case it would be a waste of valuable human life time to waste it on freeing stuck valves just to hear it run before the teardown.
On the other hand if you aren't really doing a full restoration then you are back to heat and penetrant and tapping on the valve stem with a brass punch. Start by pulling the head. This will allow you access to the top of the valves. Now you can build a small dam around the heads of the valves using anything handy with duct tape. Now you can puddle penetrant on top of the valve so it can seep downhill. Some valves you thought were closed will actually be cracked open. Now you have the option of prying them loose or trying to tap down & up to break them loose. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
Brumbach Member
Joined: Jun 18, 2013 Posts: 178
|
Posted: Fri Mar 25, 2016 8:39 am Post subject: |
|
|
The engine is pulled and on a stand, partially disassembled. I'll be pulling the crank and cam next. Essentially, I'm stripping the block for cleaning, honing or boring, etc. The more work I do, the less the machine shop has to do. Should the cam slide out with the valves stuck in a closed position? Possibly, rotating it as I pull it out? |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16355 Location: Wisconsin
|
|
Back to top |
|
|
Brumbach Member
Joined: Jun 18, 2013 Posts: 178
|
Posted: Fri Mar 25, 2016 9:37 am Post subject: |
|
|
Not yet. Trying to uncover my spring compressor that's buried in my basement somewhere. I usually have two of everything because I can never find the original when I need it. One of these days I'll get organized. |
|
Back to top |
|
|
charlesfitton Member
Joined: Jun 07, 2010 Posts: 69 Location: Maryhill On
|
Posted: Sat Mar 26, 2016 8:22 am Post subject: |
|
|
Should the cam slide out with the valves stuck in a closed position? Possibly, rotating it as I pull it out?
If you are concerned at all, back off the adjusters first... |
|
Back to top |
|
|
Brumbach Member
Joined: Jun 18, 2013 Posts: 178
|
Posted: Sat Mar 26, 2016 6:23 pm Post subject: |
|
|
Wouldn't rotate enough to back out the cam. I'll lower the adjuster and try that. Thanks |
|
Back to top |
|
|
|