adjusting drag link m38a1

ktm25089 · Member Joined: Mar 02, 2008 Posts: 48

Hello,
just to verify what the manual says
tighten the bolts and the loose the one turn and a half???
is that correct??

Thank you
George

4x4M38 · Posted: Mon Aug 15, 2016 3:44 pm Post subject:

George,
Which end?

Look at page 269. (1) Gear end is different than (2) axle end.

Gear end: Tighten, then back off 1/4 turn and until one of the slots aligns with the cotter pin holes.

Axle end: Tighten, then back off 1/2 turn and until one of the slots aligns with the cotter pin holes.

Take care,
_________________
Brian
1950 M38
MC11481
http://www.willysmjeeps.com/v2/modules.php?set_albumName=album372&op=modload&name=gallery&file=index&include=view_album.php

ktm25089 · Member Joined: Mar 02, 2008 Posts: 48

need both ends,
1/4 and 1/2 only?ok,i will try that.

wesk · Posted: Mon Aug 15, 2016 8:25 pm Post subject:

Make sure you have the correct end forward! Also the two ends share the same set of parts but the two ends are not assembled in the same order.

A, E, C & D are the same but in a different order at each end.

The threaded plugs "G" are different.

_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100

Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php

4x4M38 · Posted: Mon Aug 15, 2016 8:49 pm Post subject:

Note that there are two part C ball seats back to back on the gear end.
_________________
Brian
1950 M38
MC11481
http://www.willysmjeeps.com/v2/modules.php?set_albumName=album372&op=modload&name=gallery&file=index&include=view_album.php

wesk · Posted: Mon Aug 15, 2016 9:44 pm Post subject:

Actually the two "C" washers which are concave on one side are not back to back on the aft end of the link. They are concave face to face with the ball from the end of the pitman arm in between them.

On the front end there is only one "C" washer because the threaded plug's inner face is concave for the forward side of the ball off the steering bellcrank and "C" washer's concave face is facing forward against the back side of the ball..

I actually had a illustration for this in my photo album with all the rest of these very educational photos that so few people take advantage of!

_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100

Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php

ktm25089 · Member Joined: Mar 02, 2008 Posts: 48

ok,checked for the ends and the assembly of the parts.
after i will tight the bolts how much to loose them?
1/2 and 1/4 turn as 4x4m38 says?

thanks

4x4M38 · Posted: Tue Aug 16, 2016 1:28 pm Post subject:

Yes, Wes,
What I was trying to say was that there were two in total of those
on that end. You were much clearer as usual.
_________________
Brian
1950 M38
MC11481
http://www.willysmjeeps.com/v2/modules.php?set_albumName=album372&op=modload&name=gallery&file=index&include=view_album.php

wesk · Posted: Tue Aug 16, 2016 6:14 pm Post subject:

ktm25089 · Member Joined: Mar 02, 2008 Posts: 48

Done!!!
Thanks all for the help!! Very Happy

oreo3156 · Member Joined: Jan 22, 2007 Posts: 95

was just going to post this question but found this thread searching, awesome info!
_________________
53 m38a1 63 cj3b

Rocket · Member Joined: Jul 28, 2018 Posts: 2

Good afternoon, new to the site, but I have a similar question. I understand that the manual states to tighten and then loosen the adjustment plugs, my question is just how tight do you make them, i.e. where do you start? It is a 1 hex, you can tighten them a good deal, but you don't want to crush the ball ends.
Thanks.

wesk · Posted: Sun Sep 02, 2018 6:47 pm Post subject:

None of the pubs, military or civilian, offer a torque amount. The civilian books use the terminology "screw in the plug until it is firmly against the ball. I would say in this case "Tighten" & "Firmly" mean until there is no play.
_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100

Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php

Rocket · Member Joined: Jul 28, 2018 Posts: 2

Thank you. I'll do a bit of trial and error, snug but not too snug...


Create an account	Home · · Forums · · Articles · · Downloads · · Photo Gallery


PHP-Nuke Copyright © 2005 by Francisco Burzi. This is free software, and you may redistribute it under the GPL. PHP-Nuke comes with absolutely no warranty, for details, see the license.