View previous topic :: View next topic |
Author |
Message |
JeepdaddyRC Member
Joined: Jan 10, 2020 Posts: 175
|
Posted: Wed Apr 28, 2021 1:14 pm Post subject: Death wobble, have I tried everything |
|
|
The following have been taken to find the M38A1 wobble:
- Rebuilt steering box with new shaft and sector
- New drag link, adjusted to spec
- Rebuilt bell crank with new bearings
- New tie rod ends
- New shocks
- Tires inflated to 25 lbs
- New wheel bearings and races
- New king pin bearings and races
- Steering knuckle bearing preload set to 9 lbs of pull based TM9-8014, p 257 (5)
The wobble is still there. What am I missing? |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16365 Location: Wisconsin
|
Posted: Wed Apr 28, 2021 3:57 pm Post subject: |
|
|
With the front wheels off the floor, the steering wheel anchored dead tight/still is there any play/slop in any off the repaired/replaced units. If so exactly how much. Please give play in a measurement not an adjective. Exactly how much travel measured at the top of each front tire and at the front of each front tire?
Finally are both front wheels perfectly true/straight? _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
Mike_B Member
Joined: Dec 10, 2017 Posts: 338 Location: Southern Maryland
|
Posted: Wed Apr 28, 2021 8:18 pm Post subject: |
|
|
Don't overlook the leaf spring pins and shackles...
Mike B _________________ Mike B
1953 M38A1 Brush Truck
1952 M38
1951 M100 Trailer |
|
Back to top |
|
|
RonD2 Member
Joined: Oct 02, 2014 Posts: 2004 Location: South Carolina, Dorchester County
|
Posted: Wed Apr 28, 2021 8:56 pm Post subject: |
|
|
JeepDaddy usually always posts his questions both here and the G503 forum (M38/M38A1 tech forum) at the same time. He usually gets quite a bit of feedback, answers, and suggestions in both places at the same time, with the expected overlap. Both forums seem to be helpful of what he needs with good stuff, but keeping up with it all is kind of a chore. I've noticed that one forum or the other usually fades away with no solution ever posted to close it out for the audience. The good news is that usually he titles both threads the same, which simplifies the searching feature. _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
|
|
Back to top |
|
|
JeepdaddyRC Member
Joined: Jan 10, 2020 Posts: 175
|
Posted: Thu Apr 29, 2021 8:45 am Post subject: |
|
|
I will report back with results.
It is helpful for future readers to provide a summary/conclusion.
Hopefully I can pinpoint the issue because the wobble begins at a slow speed (25-35 mph), triggered by only minor bumps in the road - but it is pretty violent. The PO's steering stabilizer was a band aid. |
|
Back to top |
|
|
JeepdaddyRC Member
Joined: Jan 10, 2020 Posts: 175
|
Posted: Thu Apr 29, 2021 12:40 pm Post subject: |
|
|
As promised here is the video link.
Please note this was filmed with a wide angle GoPro focusing on the driver side knuckle and tie rod end.
The tires are almost new 16x7 Military NDCC.
The first view is regular speed, followed by slow motion. This occurred at 28 mph over minor bumps in the road.
https://www.youtube.com/watch?v=NHu-jmiR5jM |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16365 Location: Wisconsin
|
|
Back to top |
|
|
JeepdaddyRC Member
Joined: Jan 10, 2020 Posts: 175
|
Posted: Thu Apr 29, 2021 1:15 pm Post subject: |
|
|
Wes, what do your expert eyes (with decades of experience) see in that video that I can't spot that indicates a very bent rim or tire issue?
Last edited by JeepdaddyRC on Thu Apr 29, 2021 3:26 pm; edited 1 time in total |
|
Back to top |
|
|
Mike_B Member
Joined: Dec 10, 2017 Posts: 338 Location: Southern Maryland
|
Posted: Thu Apr 29, 2021 1:56 pm Post subject: |
|
|
What I see is a lot of left to right movement of the springs and shocks...could just be a side effect, but...
Jack the jeep up and set it on a good set of jack stands so it won't fall off. Then see if you have side to side movement of the entire front suspension while pushing/pulling on the tires with your hands at 3 and 9 o'clock. It may take two people, one shacking it hard while one is looking/feeling for movement at the shackles and pins...
Mike B _________________ Mike B
1953 M38A1 Brush Truck
1952 M38
1951 M100 Trailer |
|
Back to top |
|
|
RonD2 Member
Joined: Oct 02, 2014 Posts: 2004 Location: South Carolina, Dorchester County
|
Posted: Thu Apr 29, 2021 3:32 pm Post subject: |
|
|
Not to distract from troubleshooting, but what's that large shiny silver bracket clamped around the axle on the inboard side of the spring pack? _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
|
|
Back to top |
|
|
JeepdaddyRC Member
Joined: Jan 10, 2020 Posts: 175
|
Posted: Thu Apr 29, 2021 4:48 pm Post subject: |
|
|
RonD2,
Good observation and question.
That is the one of the brackets from the PO's steering stabilizer. The other bracket is on the passenger side tie rod.
I removed the stabilizer shock absorber, but not the brackets yet.
Apparently the stabilizer was the POs answer to "a little shimmy". |
|
Back to top |
|
|
RonD2 Member
Joined: Oct 02, 2014 Posts: 2004 Location: South Carolina, Dorchester County
|
Posted: Thu Apr 29, 2021 5:12 pm Post subject: |
|
|
Thanks JeepDaddy.
That kind of leads me to another question.....the TM has a procedure and measurements with tolerances for checking frame straightness, true and square. Plumb-bob, pencil, tape measure, and flat garage floor are all that's needed. Out of curiosity, have you checked it?
You mentioned that you did a front wheel alignment for correct toe-in. I'm guessing unless you did that yourself, any shop you took it to for alignment would probably have discovered a bent frame and told you.
Even without death wobble, I couldn't resist checking mine. It came out within specifications. Kind of amazing after 65+ years.
Just a thought.
It's obviously much easier to swap front wheels with the rear to see if that's the problem, and to re-check torque value on every part involved (both good ideas) than it would be to deal with a bent frame.
I'm only asking because maybe the PO had a problem he couldn't solve without the dampener? Assuming there was no wobble or "shimmy" before you disassembled and rebuilt the steering? Or was there?
Good luck! _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
|
|
Back to top |
|
|
JeepdaddyRC Member
Joined: Jan 10, 2020 Posts: 175
|
Posted: Thu Apr 29, 2021 9:23 pm Post subject: |
|
|
These nice original early M38A1 4.5x16 military wheels (with 1/8 pilot hole and safety bead) are headed to the wheel and tire pros for evaluation.
I will also continue the search for "hidden" steering play and report back.
I now believe the PO could not locate the issue, gave up, and added a steering stabilizer.
I am determined to figure out this mystery.
Appreciate the help. |
|
Back to top |
|
|
Mike_B Member
Joined: Dec 10, 2017 Posts: 338 Location: Southern Maryland
|
Posted: Thu Apr 29, 2021 9:57 pm Post subject: |
|
|
Have you had the tires balanced?
Mike B _________________ Mike B
1953 M38A1 Brush Truck
1952 M38
1951 M100 Trailer |
|
Back to top |
|
|
JeepdaddyRC Member
Joined: Jan 10, 2020 Posts: 175
|
Posted: Fri Apr 30, 2021 10:40 am Post subject: |
|
|
We have our first clue in the mystery.
Followed Wes's diagnostic procedure of firmly anchoring the steering wheel, raising the front end on jackstands and moving tires back and forth - with the goal to locate any play/looseness.
Results with steering wheel anchored:
1. No play at tire/wheel when grasped at 12:00 and 6:00 o'clock position (the king pin bearings and wheel bearings were just replaced).
2. One inch of play in each direction at tire/wheel when grasped at 3:00 and 9:00 o'clock positions and moved side to side (without movement of steering wheel)!
3. Tie rod ends moving with tire
4. Drag link moving with tire
I believe the "play" is narrowed down to the steering gear. The PO replaced the sector shaft, worm drive and pitman arm. You can feel slight movement up and down in the steering wheel (towards the driver) without the steering wheel turning with someone moving the tires back and forth at 3:00 and 9:00 o'clock.
Thoughts? |
|
Back to top |
|
|
|