The image at the top left, the arrow pointing to the LR antenna (for the RT-70) states that items 17, 18, 19, 21 & 20 are needed for the -7. Is that for both antennas or just the LR? I would assume both antennas, because the frequencies ranges of both RTs and auxiliary Rx are so similar.
Also, when I look up the items, the -7 calls for:
(QTY1) Item #18 (MS-117A)
(QTY1) Item #20 (AB-22/GR)
(QTY2) Item #21 (AB-24/GR)
Items 17 (MS-116-A) & 19 (MS-118-A) are not used on the -7. So, that would mean 4 sections to each antenna assembly; correct? I'm thoroughly confused.
AB-24/GR has a small ball at the tip and does not accept another rod on top of it. If the -7 calls for 2 of these sections (-24), I would have to assume that one goes at the top of each antenna.
Do all successive (progressively smaller) sections screw inside its mating (lower) section? The -117 I have (longest of them all) is longer than the -22, but has the same size ends, so they don't attach to each other unless I slide one over the other (versus screwing them together).
The only way this makes sense to me (at this point) is that one antenna assembly consists of the (1) -117 and (1) -24, and the other antenna assembly consists of (1) -22 and (1) -24. That's the only way I see to make 2 antennas out of this pile of sticks.
-Rich
ETA: I edited the drawing for clarity and removed some items:
I'm assuming that it wouldn't hurt to put some copper anti-seize on the threaded connections after they've been cleaned and before they're put together?
Joined: Oct 02, 2014 Posts: 2005 Location: South Carolina, Dorchester County
Posted: Thu Sep 19, 2024 8:43 am Post subject:
Unless you intend to leave your antenna assembled for super long periods of time (months, years), or are in a very harsh environment (ex: salt water and air) anti-seize or dielectric compound shouldn't be necessary.
While it wouldn't hurt anything, like any grease it captures dirt and displaces moisture --- and that doesn't make the joint "maintenance free".
The antenna should still be periodically disassembled, cleaned, and inspected.
If you don't use anti-seize or dielectric grease then that's one less thing to buy, clean off (and re-apply).
Whether or not you use anti-seize or dielectric grease, it's good to wrap the mated joints (after screwing them together) with a few turns of good quality electrical tape (or self-fusing rubber tape) to keep crud and water out of the joint.
These antenna elements are rather fragile, especially if tied down or slapping tree branches and the like.
Radio guys carried spare elements by the handfuls.
And they only need to be screwed together snug by hand (don't crank down on them hard). Known to split. _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
Last edited by RonD2 on Thu Sep 19, 2024 8:51 am; edited 1 time in total
In that case I'll likely just keep using the copper anti seize. I've got enough of it to last 2 lifetimes, and it's a heck of a lot cheaper than my good coax tape. I don't mind cleaning it off and reapplying it if it means the joints will come apart easier. I had a heck of a time taking apart the antenna that was on it when I got it. Who knows how long it had been together or how it was tightened, but it was a bear.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
