View previous topic :: View next topic |
Author |
Message |
Ryan_Miller Site Administrator
Joined: Apr 03, 2005 Posts: 1635 Location: Kansas
|
Posted: Wed Oct 04, 2006 6:33 am Post subject: Brake fluid question! |
|
|
I have read through all the threads on the G503 and looked up stuff on the internet and I cannot get a clear answer.
Brake fluid seems to be a personal preference and application specific determination.
I have synthetic brake fluid (silicone) DOT 5 if I remember correctly. I was thinking of using it on my M38.
However, I know that Wes hates Dot 5!
There is a LMA (Low moisture avidity) DOT 4 (I think) that seems to show promise.
I was curious as to the experiences and opinions of our group.
Ryan _________________ Ryan Miller
MVPA # 22010 |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16283 Location: Wisconsin
|
Posted: Wed Oct 04, 2006 8:50 am Post subject: |
|
|
DOT 5 belongs in your enemy's vehicles!
DOT 5 does not retain moisture suspended in it's molecular construction like DOT 3. So the moisture goes directly to the low spots and corrodes things quickly.
DOT 5 traps air molecules and prevents a real quality bleeding.
DOT 5 doesn't tolerate heat well. I think your Exhaust is about 8" away.
DOT 5 is much more expensive than DOT 3. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
Jeeps4Brains Member
Joined: Apr 15, 2005 Posts: 133 Location: Up State SC
|
Posted: Wed Oct 04, 2006 9:23 am Post subject: |
|
|
I knew that response was coming.
I like new stuff just as much as the next guy but I read up on it too. I feel like if you bleed the brakes and replace the fluid every 2 years you are better off than with silicon.
I read where the dirt bike crowd do not like it and they usually go for anything that gives them an edge.
Up to you though. |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16283 Location: Wisconsin
|
|
Back to top |
|
|
Ryan Member
Joined: Jan 10, 2006 Posts: 136 Location: Russellville, AR
|
Posted: Wed Oct 04, 2006 10:19 am Post subject: |
|
|
I have always stuck to good old DOT 3 brake fluid and have never had any problems with any of my vehicles. |
|
Back to top |
|
|
maeserik Member
Joined: Jun 14, 2006 Posts: 226 Location: Wijnegem Belgium Europe
|
Posted: Thu Oct 05, 2006 4:38 am Post subject: |
|
|
After rebuilding the whole brakesystem, i filled it with DOT4.
There is told to me to drive the jeep regulary to keep the brakesystem in order, change the fluid every year ot two years.
Dot 5 is absorbs no water, and you need not much water to get corrosion at all the iron brake cylinders ! _________________ 1942 GPW 71336 my son's jeep restored now
1951 M38 MC11891
1953 VW beetle (genuine german Käfer )
1957 fantastic wife
http://www.surfacezero.com/g503/showgallery.php?cat=1865
and this webside |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16283 Location: Wisconsin
|
|
Back to top |
|
|
TomM Moderator
Joined: Apr 18, 2005 Posts: 458 Location: Rhode Island
|
Posted: Thu Oct 05, 2006 3:51 pm Post subject: Silicone fluid |
|
|
I am the enemy. I use Silicone fluid.
My practical experience: After rebuilding my GPW brakes back in the early 80's and filling with Castrol LMA I thought I was all set. Within a few years there were problems due to moisture. The jeep was stored in a damp but not wet garage. The fluid had sucked up tremendous amounts of water from the air. When I tore the brake system apart 10 years after rebuild all wheel cylinders were rusted and the MC was junk. Another total rebuild followed, lines, hoses, WC's and MC's. In 1998 I filled it with Silicone. This past spring I put a light down into the MC and it is as clean as it was new.
The right thing to do is change the fluid. I will admit it has not been done regularly. Next spring. I keep the jeep in a much dryer place than it had been back in the 80's now too. So far its all looking good.
I also run silicone in a plastic Chevy for the past 10 years. The disc brake systems in those were horrors for moisture intrusion for a number of reasons. The calipers have now been converted to stainless sleeves with o-rings on the pistons. I did take them apart 2 winters ago to inspect them and drained as much fluid from the system as I blast out. There wasn' any evidence of water in the system either due to damage or drops in the fluid that I could detect. I suspect because silicone doesn't accept water vapor as readily as DOT3 that much of the future water problems would come from rain driving, washing etc. Whereas, it seems that even the LMA DOT3 sucks up quite a bit of water via vapor. Later cars with ABS cannot run silicone.
The following qualifiers apply. Neither vehicle sees rain or winter duty - almost never. They don't get washed much either. Moisture problems would be from air/water vapor. I'm only guessing but thats probably the source for most brake system moisture issues anyway.
If you are going to a high altitude from low you will need to pay additional attention to bleeding your silicone equipped brake system. It is a bit of a job to bleed these.
I have had excellent service from silicone in these cars that don't get a whole lot of road use and would do it again.
Similarly my 89 blazer has DOT 3 fluid and I have never had to change a line. I have changed the rubber hoses, wheel cylinders and calipers a couple times in the past 250k miles. The MC is original.
Sorry Ryan, no answer to this one. Its your decision and certainly there is a lot of experience pro and con out ther. But I have used the dreaded, evil silicone and it has served me well. There is a reasonably good chance that I will use it in my M38 when I get to putting the brake system back in.
fire away...this one always leads to a lively debate.
Maybe we can change the topic to paint colors......
Tom |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16283 Location: Wisconsin
|
Posted: Thu Oct 05, 2006 5:53 pm Post subject: |
|
|
Hello Tom,
No firing today. To each his own. Obviously your 10 year layover on the DOT 3 was at fault since it should have been flushed and serviced every two years.
I won't waste my dime on silicon. That's my choice. I definately wouln't use it where it was exposed to high temps like big disc brakes.
The military fairs well with it because they are a religeous fleet operator. That is to say they over maintain their fleet with all the extra manpower and stateside spare time.
I've owned various oldies for longer than 20 years and the only rusty master cylinders I get are on the new ones to the roost right when I purchase them and bring them home. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
TomM Moderator
Joined: Apr 18, 2005 Posts: 458 Location: Rhode Island
|
Posted: Thu Oct 05, 2006 9:10 pm Post subject: |
|
|
Hi Wes,
No doubt on my fault. That Jeep sat 10 years as life caught up with me and it suffered a bit.
Here's another way to look at this because whenever ithis topic comes up it gets me to thinking.
If this were a daily driver in all weather or a jeep that I were trail riding and fording rivers I would tend to go the traditional way - stay away from silicone and change your DOT 3 frequently.
But, I cant help thinking a vehicle that sits for a long time might do well with silicone. The tendency of the fluid to act as a spoge, like DOT 3 does, is the only means for moisture to get into the system. The moisture content or puddling in low spots might be minimized or zero for these Sunday drivers.
Disc brakes - Dot 5 has a boiling point at 550 deg F. DOT3 has a boiling point around 300 deg F. so heat tolerance is reasonable except heavy braking like racing. Is it the air pumping from disc brakes that would make someone shy away from using it with Discs?
Tom |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16283 Location: Wisconsin
|
Posted: Thu Oct 05, 2006 11:11 pm Post subject: |
|
|
The heat problem is related to the difficulty expunging all air from the silicon when bleeding. The trapped molecules of air expand rapidly with the heat and the pedal will suddenly become a bit more spongy then it usually is. I also believe DOT 5 expands quicker and a little more than DOT 3 when heated.
I'm a dollar and sense guy. Both fluids come with a routine periodic flush recommendation from their manufacturers. The DOT 5 is 3 to 5 times more expensive then the DOT 3.
The only trait of DOT 5 that I like is it's friendly to paint. But with an older vehicle with the master cylinder under the floor who cares! _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
Cacti_Ken Member
Joined: Apr 20, 2005 Posts: 1021 Location: Silsbee, Texas
|
Posted: Fri Oct 06, 2006 6:51 pm Post subject: |
|
|
If one wanted to use DOT 4 in a system which has DOT 3 in it, How would you go about changing it to DOT 4?
Just flush the system DOT4? _________________ Tropical Veteran
35th Inf. Reg. "CACTI" 4th I.D. VN
Amateur Radio K5XOM |
|
Back to top |
|
|
Avalon01 Member
Joined: Oct 18, 2005 Posts: 37 Location: WI
|
Posted: Fri Oct 06, 2006 7:13 pm Post subject: |
|
|
Is DOT 4 also good for an M38A1?
Phil _________________ 1952 USMC M38A1 - In progress!
1985 M1009 |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16283 Location: Wisconsin
|
|
Back to top |
|
|
|