View previous topic :: View next topic |
Author |
Message |
ocwd Member
Joined: May 14, 2007 Posts: 721 Location: Placentia, CA
|
Posted: Sat Sep 18, 2010 7:49 am Post subject: Tub |
|
|
Nice work on the tub Dave. Did you use a lot of filler? |
|
Back to top |
|
|
53a1 Member
Joined: Jun 25, 2008 Posts: 583 Location: Kern Co.
|
Posted: Sat Sep 18, 2010 8:49 am Post subject: |
|
|
Thanks Dave.
Yes I have filler all over the jeep but I used far less than what was on there before. I pounded out the dents so there is less than 1/8'' Bondo in most places. Plus I had to add several sheet metal patches and they are very hard to get smooth. The spot I repaired next to the hood hinge had a pound of Bondo before I made a new patch. After I finished it just needed a skim to fill the imperfections in my welding and grinding.
Personally I have no problem with Bondo as long as there is a solid repair underneath.
How is the tub for yours? Does it need body work? _________________ '53 M38A1 X2
Last edited by 53a1 on Wed Dec 15, 2010 7:12 pm; edited 2 times in total |
|
Back to top |
|
|
ocwd Member
Joined: May 14, 2007 Posts: 721 Location: Placentia, CA
|
Posted: Sat Sep 18, 2010 10:41 am Post subject: Tub |
|
|
I am not sure what is needed on my tub. One of the previous owners started cosmetic restoration. He finished the driver's side and it looks pretty good but I can tell that it's just not quite right. I will start the tub pretty soon. The rear corners need some serious help but I won't know for sure until I strip off the old paint and filler.
I am still struggling with the fuel pump installation. I know it's the right pump but it just seams like it's not. The top bowl hits the front engine plate when I try to install it. |
|
Back to top |
|
|
53a1 Member
Joined: Jun 25, 2008 Posts: 583 Location: Kern Co.
|
Posted: Sun Sep 19, 2010 9:57 am Post subject: |
|
|
Dave,
If it were me I would strip the paint off and look for rust stains or cracking in the Bondo. If it looks clean and they didn't use too much I would keep it. I've found that if you get fanatical with the body work it will take way to much time and skill to finish.
My rear corners must have been wasted at some point bad but the previous owner pounded them out and welded them. I stripped his repair down to metal, sanded, treated with Phosphoric Acid then re-Bondo.
I would check the usual suspect areas like behind the brace at the kick board, tool box and under hat channels. If you don't have to fix these areas you have a very nice tub. _________________ '53 M38A1 X2 |
|
Back to top |
|
|
ocwd Member
Joined: May 14, 2007 Posts: 721 Location: Placentia, CA
|
Posted: Sun Sep 19, 2010 9:50 pm Post subject: Tub |
|
|
I am planning on having the entire tub sand blasted. I can see that someone repaired the area around the gas tank neck and the tank does not line up properly in that area. I can also see damage to both wheel houses directly behind the seats and in both rear corners. I would like to also construct a turn table so I can work on the tub and rotate it easily with out help. |
|
Back to top |
|
|
aaron92685 Member
Joined: Feb 07, 2010 Posts: 25 Location: Avondale, AZ
|
Posted: Tue Dec 14, 2010 11:50 pm Post subject: |
|
|
I love this build. I can't wait for mine to get to this point. Good job! |
|
Back to top |
|
|
53a1 Member
Joined: Jun 25, 2008 Posts: 583 Location: Kern Co.
|
Posted: Wed Dec 15, 2010 7:09 pm Post subject: |
|
|
Thanks Aaron.
It's been on hold for a couple months because I moved to a new house. I'm pretty much ready to finish it up. I've been side tracked with a '74 Yamaha Enduro DT250 that was given to me that needs a rebuild.
I have a sickness for machines and machinery. _________________ '53 M38A1 X2 |
|
Back to top |
|
|
53a1 Member
Joined: Jun 25, 2008 Posts: 583 Location: Kern Co.
|
Posted: Wed Feb 16, 2011 6:30 pm Post subject: |
|
|
I finished my Yamaha and started back on the Jeep. Wanted to get the floor pan in place so I could start driving it a little. My son is having a blast driving on my lap around the block. Took him on the Yamaha also.
http://www.youtube.com/watch?v=bUEf_QDbmhQ
_________________ '53 M38A1 X2 |
|
Back to top |
|
|
ocwd Member
Joined: May 14, 2007 Posts: 721 Location: Placentia, CA
|
Posted: Thu Feb 17, 2011 8:28 am Post subject: Pictures |
|
|
Post some more pictures Dave. It helps to motivate me. |
|
Back to top |
|
|
aaron92685 Member
Joined: Feb 07, 2010 Posts: 25 Location: Avondale, AZ
|
Posted: Thu Feb 17, 2011 5:28 pm Post subject: Re: Pictures |
|
|
ocwd wrote: | Post some more pictures Dave. It helps to motivate me. |
I agree! |
|
Back to top |
|
|
Balvar24 Member
Joined: Sep 05, 2009 Posts: 191
|
Posted: Thu Feb 17, 2011 5:36 pm Post subject: |
|
|
Are those new screws holding down you're floor panels? Where'd you get them? |
|
Back to top |
|
|
53a1 Member
Joined: Jun 25, 2008 Posts: 583 Location: Kern Co.
|
Posted: Thu Feb 17, 2011 11:11 pm Post subject: |
|
|
I ran out of OD so the bolts only got primer for now.
I sand blasted these bolts in my Harbor Freight setup. I stick them in a piece of cardboard thread first, sand blast all the heads at once then wire wheel the rest. It takes about 10 minutes to do them this way. I then soak them with phosphoric acid and rinse them prime.
Not a lot of new pictures becuase progress has been slow. _________________ '53 M38A1 X2 |
|
Back to top |
|
|
GIJOE290 Member
Joined: Apr 13, 2005 Posts: 265 Location: Altamonte Sprgs, FL 32714
|
Posted: Fri Feb 18, 2011 8:29 am Post subject: |
|
|
Wow, really nice job! My glasses are starting to fog up. _________________ David M.
08/1953 M38A1
Serial #56535
"The Green Goat"
Restoration Begins Summer 2005! ...Er Maybe 2006? 2010? 2015? 202...? |
|
Back to top |
|
|
53a1 Member
Joined: Jun 25, 2008 Posts: 583 Location: Kern Co.
|
Posted: Sat Apr 09, 2011 10:12 pm Post subject: |
|
|
I couldn't figure out why my ground strap had three holes but John at Midwest explained it. It loops from the generator bolt under engine mount plate, center hole bolts to the engine mount plate, then it bolts to the motor mount. I used external tooth washers to dig into the metal. Tested Ohms at various points and it is well grounded.
I had trouble digging up info on this so hope this helps someone out.
_________________ '53 M38A1 X2 |
|
Back to top |
|
|
53a1 Member
Joined: Jun 25, 2008 Posts: 583 Location: Kern Co.
|
Posted: Mon Apr 11, 2011 8:19 pm Post subject: |
|
|
Finished the fenders. Passenger side needed some welding, hammering and bondo but was in otherwise solid condition. I'm going to paint them when I finish the hood, dash & seats.
Installed hub caps, battery box screws and ground wire from Midwest.
Had trouble aligning the seams on fenders and had to raise the tub in the rear to take the strain off the seams. You can see the light comming between the rear bumper and tub - about and inch. I don't think this is correct.
_________________ '53 M38A1 X2 |
|
Back to top |
|
|
|