Joined: Feb 09, 2014 Posts: 178 Location: Tri Cities, Washington
Posted: Fri Jan 29, 2016 10:52 pm Post subject: Generator not charging
OK, here we go. I bought everything at MWM so I know I have good/correct stuff. I polarized the gen. tested the generator output via Wes' method, it put out 32 volts. Hooked up solid state voltage regulator, the voltage meter, the one you use the spider on. At first I had the needle in the yellow and barely in the green. But when I checked the voltage with a VOM meter I only had 20-22 volts. It was a ground problem. The connections between the motor mount and block wasn't sanded bare. fixed that and I had the needle buried into the green and had 24-26 volts. Now it's about 10 miles later and the needle sinks back into the yellow. I cleaned the grounds between the block and motor mount, battery and frame, the bezel in the cluster dash. Battery connections are solid, any ideas? I checked the volts on the starter when I check for voltage.
Thanks in advance _________________ Rusty, 1952 M38, Koenig hard top.
The first thing you do is isolate the problem. Full field the generator again. If it is ok then continue troubleshooting the connections, harness and regulator.
Don't overlook the ground between the generator and the regulator. I know the harness shield is suppose to do that but it can do that only if there's no paint between the shield and the connectors and no paint or corrosion between the connectors of the harness and the receptacles on the regulator and generator.
If you reach an impass with the generator ok and the harness and connections checking good you are back to the regulator. As far as I know none of the vendors will take back a transistorized regulator. There are no published manuals on the transistorized regulator. This is why I do not buy them or try to work on them. The mechanical regulators do just fine and have tech data and parts for repairs. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Joined: Feb 09, 2014 Posts: 178 Location: Tri Cities, Washington
Posted: Sat Jan 30, 2016 1:49 pm Post subject:
Would a continuity test with an VOM be sufficient to test the cable from the Gen to the voltage reg? _________________ Rusty, 1952 M38, Koenig hard top.
Joined: Feb 09, 2014 Posts: 178 Location: Tri Cities, Washington
Posted: Sat Jan 30, 2016 1:50 pm Post subject:
Has anyone heard of the success rate of the solid state regulator? I haven't read anything negative about them. _________________ Rusty, 1952 M38, Koenig hard top.
The Army switched to them because they were more reliable and, at the time, cheaper. They were an XB3 item from supply. That means they were not repairable and were a throw away item. The 24V 25 Amp system has been out of use over30 years and the production of spare parts for that system ended about the same time. The nos stuff on the market is only reliable as it,s conditions of storage allow it to be. They are usually (NOS) pretty dependable for awhile. But as I said there is no spare parts, or manuals to support them. They cost 3 to 4 times their original value today and are still a throw away item when they break. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Joined: May 30, 2014 Posts: 3447 Location: Texas Hill Country
Posted: Sun Jan 31, 2016 12:20 am Post subject:
Wes,
Would you give your opinion on the non solid state regulators
both used and "nos" as being offered on various venues
versus the solid state units?
I think my opinion of solid state vs mechanical is clear above.
As for the quality of mechanical rebuilt units and used units from vendors I cannot offer one. I have never bought a rebuilt mechanical regulator from any vendor. I have bought many used from flea markets and other non-formal vending types and opened the lid and knew exactly what I was buying. I won't pay more than $30 to $40 dollars for a used one that looks very good under the cover. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
An interior photo of a solid state regulator won't help you much. The damage that can make them useless may never show.
You can usually spot overheated, corroded and pitted components of the mechanical regulator very easily in good photos. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Joined: Feb 09, 2014 Posts: 178 Location: Tri Cities, Washington
Posted: Sun Jan 31, 2016 5:17 pm Post subject:
Gen tested good, I have a new cable coming in the mail. The cable came with the jeep in a box of used stuff. Most of it that the PO acquired was either useless or wrong for that jeep. This cable looked OK to me in the beginning, but after having ground issues before, I think this cable is suspect. For me, In my opinion, I'll stick to the throw away model because that's about what I know. If I had some one to hold my hand, I would venture out to the mechanical regulator.
Thanks Wes, I'll be sure to update this thread when I have results. Threads like these keep me going. I've learned a ton. _________________ Rusty, 1952 M38, Koenig hard top.
Joined: Feb 09, 2014 Posts: 178 Location: Tri Cities, Washington
Posted: Fri Feb 05, 2016 7:33 pm Post subject:
We, new cable was not the problem. looks like I'll do some more thinking and head scratching. I hopes not the solid state voltage regulator.
Thanks _________________ Rusty, 1952 M38, Koenig hard top.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum