| Author |
Message |
 Topic: No Oil Pressure on Start Up, Advice Needed |
4Ewilly
Replies: 29
Views: 25426
|
 Forum: Technical Knowledge Base Posted: Sun Jul 01, 2018 4:31 pm Subject: No Oil Pressure on Start Up, Advice Needed |
| Thanks for the list Wes, very helpful as always. This has been a frustrating process, but I have learned a great deal.. Thanks for your advice. Yes perhaps I should push for a refund and start with ... |
| Topic: No Oil Pressure on Start Up, Advice Needed |
4Ewilly
Replies: 29
Views: 25426
|
Forum: Technical Knowledge Base Posted: Sun Jul 01, 2018 6:57 am Subject: No Oil Pressure on Start Up, Advice Needed |
| I wanted to continue this string and ask for advice as I am working back with the rebuild shop on concerns I am seeing. Since discovering the issue with the missing oil gallery plug, I have been conc ... |
| Topic: T 90 Shaft nut tool recommendation |
4Ewilly
Replies: 3
Views: 3916
|
Forum: Technical Knowledge Base Posted: Wed May 30, 2018 4:37 am Subject: T 90 Shaft nut tool recommendation |
| Good advice, thanks guys. Wes, I used an adjustable wrench to measure the nut, and it turns out that it is 1 5/16. Thanks for the help! |
| Topic: T 90 Shaft nut tool recommendation |
4Ewilly
Replies: 3
Views: 3916
|
Forum: Technical Knowledge Base Posted: Tue May 29, 2018 6:10 am Subject: T 90 Shaft nut tool recommendation |
| I am trying to remove the gear shaft retention nut on my T90 in order to separate the transmission and transfer case. I have tried a 12pt 1 1/4 socket and it is a little small and does not fit over t ... |
| Topic: M38 Pressure Plate Release Lever Clips |
4Ewilly
Replies: 2
Views: 4574
|
Forum: Technical Knowledge Base Posted: Sat May 26, 2018 7:45 am Subject: M38 Pressure Plate Release Lever Clips |
Brett:
Thanks for the reply, this makes sense to me. I found these in the TM9-8015-1 manual referred to as "Pressure plate release clips" in section 135 -E.
https://books.google.com/books?id= ... |
| Topic: M38 Pressure Plate Release Lever Clips |
4Ewilly
Replies: 2
Views: 4574
|
Forum: Technical Knowledge Base Posted: Sat May 26, 2018 5:52 am Subject: M38 Pressure Plate Release Lever Clips |
| I have a 1951 M38, and recently my clutch linkage had broke (at the cable pin connector). I pulled the transmission and found the clutch fork and pressure plate release clips (2 of the 3)in the botto ... |
| Topic: No Oil Pressure on Start Up, Advice Needed |
4Ewilly
Replies: 29
Views: 25426
|
Forum: Technical Knowledge Base Posted: Fri Jan 05, 2018 10:33 pm Subject: No Oil Pressure on Start Up, Advice Needed-Rep;y |
Good news  I put in the missing oil gallery plug, primed the system, removed the pugs and spun the engine with the starter. Immediate oil pressure. Went ahead and started her up and have pressure ... |
| Topic: No Oil Pressure on Start Up, Advice Needed |
4Ewilly
Replies: 29
Views: 25426
|
Forum: Technical Knowledge Base Posted: Mon Jan 01, 2018 9:16 am Subject: No Oil Pressure on Start Up, Advice Needed - Reply |
Wes:
Thanks for setting up my photo album and posting the photos. Your comments on the photos were very helpful. If I can find the gallery plugs locally, I will install them today, if not I will n ... |
| Topic: No Oil Pressure on Start Up, Advice Needed |
4Ewilly
Replies: 29
Views: 25426
|
Forum: Technical Knowledge Base Posted: Sun Dec 31, 2017 11:49 am Subject: No Oil Pressure on Start Up, Advice Needed - Reply |
Hi:
Sorry my photos are not viewable.. Let me try sharing the album
https://photos.google.com/share/AF1QipPoCHFke2tYItKkS-MpQHdWxh8G9zInBXHLAZRQ-JWPJcsdMVBGCJx0EGyC5X81qA?key=OEd0QlF2X29pbWtETG9 ... |
| Topic: No Oil Pressure on Start Up, Advice Needed |
4Ewilly
Replies: 29
Views: 25426
|
Forum: Technical Knowledge Base Posted: Fri Dec 29, 2017 9:41 am Subject: No Oil Pressure on Start Up, Advice Needed- Oil Plug |
Wes:
Looking up into the connection for the oil sump arm, the threaded hole that you see in the attached photo, goes into the channel that the oil sump attaches to, that goes to the oil pump. I am ... |
| Topic: No Oil Pressure on Start Up, Advice Needed |
4Ewilly
Replies: 29
Views: 25426
|
Forum: Technical Knowledge Base Posted: Thu Dec 28, 2017 9:26 pm Subject: No Oil Pressure on Start Up, Advice Needed-Rep;y |
I pulled the oil pan to check the internal oil gallery plugs. Here is a photo of what I am seeing:
http://willysmjeeps.com/v2/modules/gallery/albums/album572/1228171843_Burst01.sized.jpg
above ... |
| Topic: No Oil Pressure on Start Up, Advice Needed |
4Ewilly
Replies: 29
Views: 25426
|
Forum: Technical Knowledge Base Posted: Thu Dec 28, 2017 5:49 pm Subject: No Oil Pressure on Start Up, Advice Needed - Reply |
Wes:
Thanks for your thorough reply. I apologize for not being very responsive, I have two many irons in the fire as usual.
Based on your information, I do have an L-134 and it appears to be ... |
| Topic: No Oil Pressure on Start Up, Advice Needed |
4Ewilly
Replies: 29
Views: 25426
|
Forum: Technical Knowledge Base Posted: Wed Dec 27, 2017 8:11 am Subject: No Oil Pressure on Start Up, Advice Needed Reply |
Wes:
Thanks for your quick reply, sorry I have been slow to respond, we have family in town and lots of activities. Let me also say that I am not an experienced mechanic, but I am learning:)
In ... |
| Topic: No Oil Pressure on Start Up, Advice Needed |
4Ewilly
Replies: 29
Views: 25426
|
Forum: Technical Knowledge Base Posted: Mon Dec 25, 2017 9:28 am Subject: No Oil Pressure on Start Up, Advice Needed |
| I am looking for advice on how to troubleshoot my 1952 M38. It was recently rebuilt, and I am trying to get to a start up. When I start it, I am not getting any oil pressure at the oil gauge. Here ... |
| |
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
