Author |
Message |
Topic: Replacement Tubs |
L84dinner
Replies: 16
Views: 6045
|
Forum: Technical Knowledge Base Posted: Tue Feb 15, 2022 7:15 pm Subject: Replacement Tubs |
I have a 2013 vintage MD Juan M38 kit - tub, fenders, grill, tailgate windshield. It was lots of work making it fit and drilling or moving holes. I am told later kits are better.
My current chal ... |
Topic: YS637 Carburetor Air Horn Question |
L84dinner
Replies: 12
Views: 8620
|
Forum: Technical Knowledge Base Posted: Mon Aug 17, 2020 3:19 pm Subject: YS637 Carburetor Air Horn Question |
Just wanted to follow up and state that I was able to effectively plug the pinhole in the airhorn and it now starts and runs smooth without further flooding. Still have not resolved the fuel pump pre ... |
Topic: YS637 Carburetor Air Horn Question |
L84dinner
Replies: 12
Views: 8620
|
Forum: Technical Knowledge Base Posted: Tue Aug 04, 2020 9:09 pm Subject: YS637 Carburetor Air Horn Question |
Wes,
Thank you again for your assistance.
I disassembled the pump to see if the technical bulletin has been complied with. There is a 1/8" diameter hole drilled in the deck of the body and the oil ... |
Topic: YS637 Carburetor Air Horn Question |
L84dinner
Replies: 12
Views: 8620
|
Forum: Technical Knowledge Base Posted: Tue Jul 28, 2020 2:06 pm Subject: YS637 Carburetor Air Horn Question |
Wes,
Four digits on flange are 9585.
Some photos of fuel pump installed for reference.
http://willysmjeeps.com/v2/modules/gallery/albums/album549/AC_Pump_1.jpg
http://willysmjeeps.com/v2/m ... |
Topic: YS637 Carburetor Air Horn Question |
L84dinner
Replies: 12
Views: 8620
|
Forum: Technical Knowledge Base Posted: Mon Jul 27, 2020 3:27 pm Subject: YS637 Carburetor Air Horn Question |
I have a rebuilt AC Series CU or CY fuel and vacuum pump (no primer handle) and I have a 9/16" thick spacer between pump and block.
Thanks,
John |
Topic: YS637 Carburetor Air Horn Question |
L84dinner
Replies: 12
Views: 8620
|
Forum: Technical Knowledge Base Posted: Sun Jul 26, 2020 8:05 pm Subject: YS637 Carburetor Air Horn Question |
I rechecked pressure and confirmed its 6 1/2 psi. I noted I have motor oil in my fuel especially the first few strokes.
Looking through your archive now, Wes.
Thanks,
John |
Topic: YS637 Carburetor Air Horn Question |
L84dinner
Replies: 12
Views: 8620
|
Forum: Technical Knowledge Base Posted: Sat Jul 25, 2020 8:33 am Subject: YS637 Carburetor Air Horn Question |
Thank you for responding Wes.
Yes I have downloaded TM9- 1826A and have not found any mention of this hole nor a figure showing it. In particular I would have expected it to be labeled in Figure 5 ... |
Topic: YS637 Carburetor Air Horn Question |
L84dinner
Replies: 12
Views: 8620
|
Forum: Technical Knowledge Base Posted: Fri Jul 24, 2020 8:49 pm Subject: YS637 Carburetor Air Horn Question |
I am in the process of testing out a rebuilt L134 engine with a rebuilt YS637 carburetor. Engine starts fine but carburetor floods after a couple minutes of running.
I have been working through ... |
Topic: 1952 M38 CDN Correct Engine Colour |
L84dinner
Replies: 10
Views: 11100
|
Forum: Technical Knowledge Base Posted: Thu Jan 11, 2018 11:28 am Subject: 1952 M38 CDN Correct Engine Colour |
The lighter engine colour does pull up the detail of the accessories.
Beautiful job Jordan.
John |
Topic: 1952 M38 CDN Correct Engine Colour |
L84dinner
Replies: 10
Views: 11100
|
Forum: Technical Knowledge Base Posted: Wed Jan 10, 2018 4:06 pm Subject: 1952 M38 CDN Correct Engine Colour |
Hawkshadow found the grey engine enamel he used to be very close in colour. He thinks I have a Ford 8N colour but also notes that you can't be sure what Ford might have used. M38CDN Bill thinks my c ... |
Topic: 1952 M38 CDN Correct Engine Colour |
L84dinner
Replies: 10
Views: 11100
|
Forum: Technical Knowledge Base Posted: Tue Jan 09, 2018 6:53 pm Subject: 1952 M38 CDN Correct Engine Colour |
Yes contacted Hawkshadow and M38CDN Bill. Appears this is the correct colour.
Thanks,
John |
Topic: 1952 M38 CDN Correct Engine Colour |
L84dinner
Replies: 10
Views: 11100
|
Forum: Technical Knowledge Base Posted: Sun Jan 07, 2018 8:55 am Subject: 1952 M38 CDN Correct Engine Colour |
I have followed an earlier thread that states the M38CDNs were delivered with engines painted gray. The thread stated that the colour should be Ford 9N Gray and that this paint was available from New ... |
Topic: M38 CDN Bell Crank bellows seal |
L84dinner
Replies: 10
Views: 12788
|
Forum: Technical Knowledge Base Posted: Thu Sep 07, 2017 8:51 pm Subject: M38 CDN Bell Crank bellows seal |
Brian,
There was no spring in the original assembly and Brent did not supply one.
The seal fit fairly snug and as you can see the bell crank assembly I have shields the seal from direct exposure. ... |
Topic: M38 CDN Bell Crank bellows seal |
L84dinner
Replies: 10
Views: 12788
|
Forum: Technical Knowledge Base Posted: Wed Sep 06, 2017 8:58 pm Subject: M38 CDN Bell Crank bellows seal |
Took a while for seal to ship from Brent and clear customs but arrived and installed on the weekend.
Seal in place.
http://willysmjeeps.com/v2/modules/gallery/albums/album549/bellows_seal.size ... |
Topic: M38 spares for sale |
L84dinner
Replies: 1
Views: 6737
|
Forum: For Sale Posted: Fri Sep 01, 2017 10:24 pm Subject: M38 spares for sale |
I have a few spares left over from my rebuild.
Used M38 Steering box core requires rebuild. As-is $50.
http://willysmjeeps.com/v2/modules/gallery/albums/album549/Steering_Box1.jpg
http://willys ... |
|