Author |
Message |
Topic: Converting back to 24 Volt System? |
Oldsalt
Replies: 6
Views: 8517
|
Forum: Technical Knowledge Base Posted: Sun Oct 09, 2016 10:32 pm Subject: Converting back to 24 Volt System? |
There are some great websites that sell nothing but jeep parts. Some of the ones I've used are:
http://www.midwestmilitary.net/
http://walcks4wd.com/
http://www.mullinsjeepparts.com/
https://www. ... |
Topic: Towing |
Oldsalt
Replies: 10
Views: 11286
|
Forum: Technical Knowledge Base Posted: Thu Nov 01, 2012 7:41 pm Subject: Towing |
The trailer itself probably weighs 300 lbs or less . One person can grab the back of the trailer and drag it around although with a little difficulty. Two can lift both wheels off the ground and swi ... |
Topic: Towing |
Oldsalt
Replies: 10
Views: 11286
|
Forum: Technical Knowledge Base Posted: Wed Oct 31, 2012 7:49 pm Subject: Towing |
I have pics and drawings in my photo album of a trailer that my brother has for his jeep. It works extremely well and the jeep just drives on and off in seconds. Safety chains on each corner and awa ... |
Topic: Assembly, transfer case mount |
Oldsalt
Replies: 3
Views: 6937
|
Forum: Technical Knowledge Base Posted: Thu Sep 06, 2012 6:50 pm Subject: Assembly, transfer case mount |
Walcks has a picture of it on their site.
http://walcks4wd.com/transfer-case-mount-bolt-kit-d-18.html
The cross member is sandwiched between the smaller rubber piece and the larger steel cup. ... |
Topic: M38 Steering rebuild kit? |
Oldsalt
Replies: 2
Views: 4932
|
Forum: Technical Knowledge Base Posted: Wed Aug 08, 2012 11:10 pm Subject: M38 Steering rebuild kit? |
I can't say about Kaiser's kit but I bought one from Walcks a couple of years ago and the ball bearing for the bottom of the worm shaft was very rough. In fact the race for that bearing did not even ... |
Topic: I think I experienced "The Death Wobble" yesterday |
Oldsalt
Replies: 12
Views: 12502
|
Forum: Technical Knowledge Base Posted: Thu Jul 26, 2012 8:56 pm Subject: I think I experienced "The Death Wobble" yesterday |
Check out everything else, but overhaul the steering knuckle king pin bearings first. When they are set up correctly the front wheels are quite stiff to swing back and forth. Basically it can't shi ... |
Topic: Oil filter question |
Oldsalt
Replies: 8
Views: 32079
|
Forum: Technical Knowledge Base Posted: Sun Jul 08, 2012 9:08 am Subject: Oil filter question |
If you have the military size filter it is a Fram C-4 or equivalent. The local parts places won't usually have a listing for a military jeep. If it is the civilian size they will have a listing for ... |
Topic: Idling speed on a 55 m38a1 |
Oldsalt
Replies: 4
Views: 8118
|
Forum: Technical Knowledge Base Posted: Thu Jul 05, 2012 4:20 pm Subject: Idling speed on a 55 m38a1 |
What kind of charging system do you have. The old style generator the jeeps came with have to rev up a bit before they charge. Not charging very much at idle is normal. If you have converted to an ... |
Topic: Brent Mullins Website gone? |
Oldsalt
Replies: 3
Views: 8243
|
Forum: M Series Parts Supply & Service Review Posted: Mon Jul 02, 2012 8:41 pm Subject: Brent Mullins Website gone? |
Good to know. Thanks for the report. |
Topic: Brent Mullins Website gone? |
Oldsalt
Replies: 3
Views: 8243
|
Forum: M Series Parts Supply & Service Review Posted: Sun Jul 01, 2012 10:49 pm Subject: Brent Mullins Website gone? |
Brent Mullins website seems to be gone. If I use the address I bookmarked a long time ago it comes back as Server not found. If I use www.mullinsjeepparts.com it comes back with a test page of some ... |
Topic: Two more M38A1 questions |
Oldsalt
Replies: 4
Views: 5557
|
Forum: Technical Knowledge Base Posted: Tue Jun 26, 2012 7:12 pm Subject: Two more M38A1 questions |
There is a manual for the fording system in the downloads section of the forum that has a nice diagram for the vent/vacuum lines in it. It also has a thorough description of the purpose for each line ... |
Topic: Water Droplets on Oil Level Gauge |
Oldsalt
Replies: 6
Views: 8362
|
Forum: Technical Knowledge Base Posted: Sun Jun 17, 2012 7:01 pm Subject: Water Droplets on Oil Level Gauge |
Before taking things apart you might want to check out your PCV system to be sure it is open and working. A lack of crank case ventilation can lead to moisture in the oil in a hurry. Does your M38 h ... |
Topic: M38/M38A1 Parts |
Oldsalt
Replies: 9
Views: 11217
|
Forum: For Sale Posted: Sun Jun 10, 2012 12:15 am Subject: M38/M38A1 Parts |
What is the condition of the wiring harness?
Thanks |
Topic: Jeep is finally back |
Oldsalt
Replies: 5
Views: 6263
|
Forum: Technical Knowledge Base Posted: Thu May 31, 2012 12:59 pm Subject: Jeep is finally back |
Is your clunking a regular and rhythmic sound or is it a random clunk? If it is regular, how fast is it? Does it speed up as you go faster until it quits or does it just stay the same speed and then ... |
Topic: M-38:Heat shield between brake master cylinder and exhaust?? |
Oldsalt
Replies: 2
Views: 5182
|
Forum: Technical Knowledge Base Posted: Sun May 06, 2012 6:24 pm Subject: M-38:Heat shield between brake master cylinder and exhaust?? |
Yes there is one. Most of the MV vendors sell them. I just searched on Walcks4wd.com and found it. Most folks say that you definitely want one. |
|