| Author |
Message |
 Topic: M38A1 data plates. 1953 |
Willis
Replies: 3
Views: 10475
|
 Forum: Auctions Posted: Tue May 16, 2017 11:15 am Subject: M38A1 data plates. 1953 |
| Have these been sold? |
| Topic: M38A1 throw out bearing won't stop riding the pressure plate |
Willis
Replies: 9
Views: 12286
|
Forum: Technical Knowledge Base Posted: Tue Jul 26, 2016 7:13 pm Subject: M38A1 throw out bearing won't stop riding the pressure plate |
Solved. The clutch fork was not seated fully on the pivot ball. Once seated, I ended up having to go back to the original cable and rod. I adjusted to the 1 1/4" of play and all appears well.
Th ... |
| Topic: M38A1 throw out bearing won't stop riding the pressure plate |
Willis
Replies: 9
Views: 12286
|
Forum: Technical Knowledge Base Posted: Tue Jul 26, 2016 1:11 pm Subject: M38A1 throw out bearing won't stop riding the pressure plate |
Wes:
1. I replaced the spring for good measure. It was identical to the spring taken out.
2. I couldn't tell. The old one was so bad that it fell apart during disassembly. I do not have it an ... |
| Topic: M38A1 throw out bearing won't stop riding the pressure plate |
Willis
Replies: 9
Views: 12286
|
Forum: Technical Knowledge Base Posted: Tue Jul 26, 2016 8:13 am Subject: M38A1 throw out bearing won't stop riding the pressure plate |
Frustration has set in. Clouds are darkening. I can feel an evil presence in my garage. I'm at my wits end.
I had a bad throw out bearing which is what started me down this path. I went ahead a ... |
| Topic: YS950 - Balance Vent - Can I plug it? |
Willis
Replies: 5
Views: 7194
|
Forum: Technical Knowledge Base Posted: Sat Jul 09, 2016 12:13 pm Subject: YS950 - Balance Vent - Can I plug it? |
| Thanjs wesk. The 24 volt peripherals are long gone on this jeep. What do guys do who are running a standard distributor? |
| Topic: YS950 - Balance Vent - Can I plug it? |
Willis
Replies: 5
Views: 7194
|
Forum: Technical Knowledge Base Posted: Tue Jul 05, 2016 11:40 am Subject: YS950 - Balance Vent - Can I plug it? |
| I recently rebuilt a YS950 and the Fuel Pump for an M38a1. I installed new fuel lines. I have not installed any of the vent lines. I'm curious if I can run the jeep like this for a bit while I sou ... |
| Topic: M38a1 Bell Housing Stud/Bushing - What is it for? |
Willis
Replies: 9
Views: 10101
|
Forum: Technical Knowledge Base Posted: Thu Jun 09, 2016 8:02 am Subject: M38a1 Bell Housing Stud/Bushing - What is it for? |
Sorry about it being upside down!!
Thanks Bretto - That's exactly it.
http://willysmjeeps.com/v2/modules/gallery/albums/album167/Willis.jpg |
| Topic: M38a1 Bell Housing Stud/Bushing - What is it for? |
Willis
Replies: 9
Views: 10101
|
Forum: Technical Knowledge Base Posted: Wed Jun 08, 2016 11:25 am Subject: M38a1 Bell Housing Stud/Bushing - What is it for? |
What is the stud for coming out of this bell housing ? It was pulled from a '53
Thanks
http://i231.photobucket.com/albums/ee142/Jdog1129/m38a1_bellhousing_zpsicugbmu6.jpg |
| Topic: An M38a1 Project thread - Duke gets some loving |
Willis
Replies: 32
Views: 48514
|
Forum: Jeep Project Threads Posted: Tue Nov 03, 2015 1:50 pm Subject: An M38a1 Project thread - Duke gets some loving |
Busy couple weeks...not on the jeep though.
I was able to get the corner welded in and plan to get both fenders ready for final body work this week.
http://i231.photobucket.com/albums/ee142/Jdog ... |
| Topic: An M38a1 Project thread - Duke gets some loving |
Willis
Replies: 32
Views: 48514
|
Forum: Jeep Project Threads Posted: Fri Oct 23, 2015 10:57 am Subject: An M38a1 Project thread - Duke gets some loving |
No progress on the fender, work is getting in the way.
I did, however, receive confirmation that my newly rebuilt fuel pump is on the way. There was an electric pump on the jeep and the original f ... |
| Topic: An M38a1 Project thread - Duke gets some loving |
Willis
Replies: 32
Views: 48514
|
Forum: Jeep Project Threads Posted: Wed Oct 21, 2015 9:57 am Subject: An M38a1 Project thread - Duke gets some loving |
So, I ended up repeating your story Bryan.
Yesterday I woke up and the eye was no better. I flushed it 2 times to no avail. I made an appointment with my optometrist and drove myself to his off ... |
| Topic: An M38a1 Project thread - Duke gets some loving |
Willis
Replies: 32
Views: 48514
|
Forum: Jeep Project Threads Posted: Tue Oct 20, 2015 7:29 am Subject: An M38a1 Project thread - Duke gets some loving |
| With a little action on the slave receptacle indent on ebay, I went to work on removing the old patch. Getting all the braise out is a bit tedious, but I'm glad it wasn't welded in. I was left with ... |
| Topic: An M38a1 Project thread - Duke gets some loving |
Willis
Replies: 32
Views: 48514
|
Forum: Jeep Project Threads Posted: Mon Oct 19, 2015 1:36 pm Subject: An M38a1 Project thread - Duke gets some loving |
If you can get behind your sheetmetal go to the hardware store
and get a 1/2" copper pipe tee and beat it flat.
Put it behind where you are welding holes and hold or clamp it.
It will not stick t ... |
| Topic: An M38a1 Project thread - Duke gets some loving |
Willis
Replies: 32
Views: 48514
|
Forum: Jeep Project Threads Posted: Tue Oct 13, 2015 6:19 pm Subject: An M38a1 Project thread - Duke gets some loving |
| While waiting for the plastic to cure on the passenger fender, I pulled the driver side off. I said earlier that I had decided to cover the corners with the overlay piece from Walcks. This is what t ... |
| Topic: An M38a1 Project thread - Duke gets some loving |
Willis
Replies: 32
Views: 48514
|
Forum: Jeep Project Threads Posted: Tue Oct 13, 2015 10:12 am Subject: An M38a1 Project thread - Duke gets some loving |
Kendall - You're a kings king. Thank you much sir. I'll let you know how i make out.
I've decided to go ahead and cover up the diagonal seams on the fenders. Parts are on order.
I continued w ... |
| |
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
