Author |
Message |
Topic: brake job |
cknight
Replies: 5
Views: 6944
|
Forum: Technical Knowledge Base Posted: Wed Feb 10, 2010 7:12 pm Subject: brake job |
I always do that, assume everyone is on the same page as I. m38 |
Topic: brake job |
cknight
Replies: 5
Views: 6944
|
Forum: Technical Knowledge Base Posted: Tue Feb 09, 2010 5:06 pm Subject: brake job |
I think I will rebuild my brakes before spring. I would like to replace the shoes and also rebuild each wheel cylinder. What would be the current part number from someone like NAPA? |
Topic: Water Pump |
cknight
Replies: 4
Views: 6573
|
Forum: Technical Knowledge Base Posted: Fri Oct 05, 2007 6:31 am Subject: Water Pump |
A word of caution. I replaced my pump when I had the engine rebuilt. I took the pump to a local shop to have the pulley removed and than pressed onto the new pump. The dingbat that removed the pull ... |
Topic: Fastener |
cknight
Replies: 0
Views: 4163
|
Forum: Technical Knowledge Base Posted: Wed Oct 03, 2007 9:14 am Subject: Fastener |
Is the M38 Fastener List going to return |
Topic: M38 windshield glass |
cknight
Replies: 4
Views: 6060
|
Forum: Technical Knowledge Base Posted: Mon Oct 01, 2007 8:45 am Subject: M38 windshield glass |
Thanks for the offer. I have a glass for and m38a1 which should give the the corner radius and along with the height and width i should be able to get it.
After I get the last coat of paint on t ... |
Topic: M38 windshield glass |
cknight
Replies: 4
Views: 6060
|
Forum: Technical Knowledge Base Posted: Thu Sep 27, 2007 3:59 pm Subject: M38 windshield glass |
What is the height and width of the glass for the M38? |
Topic: attaching windshield to cowl gasket |
cknight
Replies: 2
Views: 4757
|
Forum: Technical Knowledge Base Posted: Thu Sep 27, 2007 3:54 pm Subject: attaching windshield to cowl gasket |
Yes, M38
Yes, Weatherseal
Thanks |
Topic: attaching windshield to cowl gasket |
cknight
Replies: 2
Views: 4757
|
Forum: Technical Knowledge Base Posted: Wed Sep 26, 2007 3:30 pm Subject: attaching windshield to cowl gasket |
What are the correct screws used to attach windshield to cowl gasket? |
Topic: Spring in steering column |
cknight
Replies: 2
Views: 4556
|
Forum: Technical Knowledge Base Posted: Fri Aug 31, 2007 11:20 am Subject: Spring in steering column |
What is the purpose of the spring in the steering column? |
Topic: M38a1 steering wheel color? |
cknight
Replies: 12
Views: 12442
|
Forum: Technical Knowledge Base Posted: Fri Aug 31, 2007 11:18 am Subject: M38a1 steering wheel color? |
So, If I understand form the pictures, the correct color for the M38 is green.
Correct? |
Topic: M38a1 steering wheel color? |
cknight
Replies: 12
Views: 12442
|
Forum: Technical Knowledge Base Posted: Wed Aug 29, 2007 1:00 pm Subject: M38a1 steering wheel color? |
Hey Seymour
What part of the world are you in.?
Just wondering! |
Topic: Fuel Guage sending unit wire |
cknight
Replies: 1
Views: 3896
|
Forum: Technical Knowledge Base Posted: Tue Aug 21, 2007 12:40 pm Subject: Fuel Guage sending unit wire |
Did the wire from the fuel guage sending unit to the guage have any protection on it where it is exposed from the unit to under the dash? |
Topic: Fording cable data plate |
cknight
Replies: 6
Views: 6877
|
Forum: Technical Knowledge Base Posted: Tue Aug 14, 2007 8:33 pm Subject: Fording cable data plate |
Thanks for the info.
New question.
When I mounted the fording data plate, even though the screw holes matched the dash, the hole for the cable was off by 1/4". The data plate hole is low by 1 ... |
Topic: Fording cable data plate |
cknight
Replies: 6
Views: 6877
|
Forum: Technical Knowledge Base Posted: Tue Aug 14, 2007 6:25 am Subject: Fording cable data plate |
How was the data plate for the fording cable mounted to the dash. If screwed, what would the correct screw be?
Also
What is the correct screw to hold the ring that holds the rubber boot around ... |
Topic: Delco-Remy regulator problem |
cknight
Replies: 7
Views: 11411
|
Forum: Technical Knowledge Base Posted: Fri Aug 03, 2007 7:33 am Subject: Delco-Remy regulator problem |
From personal experience, I would recomend disconnecting the battery before doing anything to the regulator. This would even include removing the cables. It is very hard to if not impossible to find ... |
|