| Author |
Message |
 Topic: M38 Starter and Generator |
cross
Replies: 0
Views: 1860
|
 Forum: For Sale Posted: Fri Jun 03, 2022 6:39 pm Subject: M38 Starter and Generator |
M38 starter MCZ-4001UT. SN G225194 This unit works and is good condition.
M38 25 amp generator, Autolite HA 4802BUT SN G532181. I have bench tested field and armature windings using ohm meter but ha ... |
| Topic: Unit Markings |
cross
Replies: 7
Views: 4380
|
Forum: Technical Knowledge Base Posted: Sat May 08, 2021 12:06 pm Subject: Unit Markings |
Dave
My father in law was in Korea in the 187th Regimental Combat Team and I have a picture of him standing in front of 2 jeeps with unit markings which he said was taken in Korea. The front bumper i ... |
| Topic: Fuel pump, antenna & gauge panel -- SOLD |
cross
Replies: 2
Views: 6096
|
Forum: For Sale Posted: Thu Nov 20, 2014 5:51 pm Subject: Fuel pump, antenna & gauge panel -- SOLD |
| M38A1 original dual action fuel pump with priming handle. This is an AC pump and includes the mounting spacer and one of the long head bolts. The pump does need to be rebuilt as the fuel diaphragm is ... |
| Topic: Antenna, bracket, mount and base |
cross
Replies: 1
Views: 5336
|
Forum: For Sale Posted: Fri Sep 05, 2014 3:34 pm Subject: Antenna, bracket, mount and base |
Complete antenna system for Willys M38 or M38A1 military jeeps. Consists of brackets, base and antenna sections listed below.
MP50 antenna mount
SCC28592 corner bracket
AB-15 mast base
MS 116,117 ... |
| Topic: Fuel tank caution warning |
cross
Replies: 2
Views: 5647
|
Forum: Technical Knowledge Base Posted: Sun Aug 18, 2013 9:34 pm Subject: Fuel tank caution warning |
Thanks for the info Wes
This would be more of a motor pool resto at best.
I have the non vented cap (WO 805012). Since you indicate this wording was actually used I'll probably just recreate what ... |
| Topic: Fuel tank caution warning |
cross
Replies: 2
Views: 5647
|
Forum: Technical Knowledge Base Posted: Sun Aug 18, 2013 11:43 am Subject: Fuel tank caution warning |
My 52 M38 didn't have the typical "caution do not overfill allow for expansion" warning below the filler cap.
Instead it had "pressurized open slowly" on 2 lines to the upper right of the filler ca ... |
| Topic: Carb rebuild kit for M38A1 (YS) carb |
cross
Replies: 5
Views: 8012
|
Forum: For Sale Posted: Sun Aug 18, 2013 11:16 am Subject: Carb rebuild kit for M38A1 (YS) carb |
Swampy
sent you a PM |
| Topic: Seat springs and cushions |
cross
Replies: 1
Views: 4285
|
Forum: For Sale Posted: Wed Mar 13, 2013 9:15 pm Subject: Seat springs and cushions |
| I have a full set (front and rear) of what I think are the original seat springs for an M38. The springs are topped with a layer of jute and then a layer of foam. Springs are rusty but not broken. The ... |
| Topic: Carb rebuild kit for M38A1 (YS) carb |
cross
Replies: 5
Views: 8012
|
Forum: For Sale Posted: Tue Mar 05, 2013 8:47 pm Subject: Carb rebuild kit for M38A1 (YS) carb |
Wes
There is no date on the kit that I can find.
I got it 2 years ago from one of the reputable suppliers and rubber is very supple. Parts were all sealed |
| Topic: Carb rebuild kit for M38A1 (YS) carb |
cross
Replies: 5
Views: 8012
|
Forum: For Sale Posted: Mon Mar 04, 2013 9:56 pm Subject: Carb rebuild kit for M38A1 (YS) carb |
| I ordered an M38 rebuild kit a while back and instead received an M38A1 kit. The box was marked wrong which I didn't find out until I opened it up. Its an APCO kit. I can send pics if needed. $25 |
| Topic: M38 fording cable length |
cross
Replies: 0
Views: 3450
|
Forum: Technical Knowledge Base Posted: Sun Feb 17, 2013 3:32 pm Subject: M38 fording cable length |
| Can anyone tell me the correct length of the fording cables for a M38. I ordered one and believe it might be for M38A1 as one cable (PCV valve) is about a foot too long. I don't mind cutting it down b ... |
| Topic: Wiring harness routing for dimmer switch |
cross
Replies: 2
Views: 7624
|
Forum: Technical Knowledge Base Posted: Sat Jun 23, 2012 11:02 am Subject: Wiring harness routing for dimmer switch |
Wes
Thanks for the pictures, that was exactly what I was looking for.
bob |
| Topic: Wiring harness routing for dimmer switch |
cross
Replies: 2
Views: 7624
|
Forum: Technical Knowledge Base Posted: Fri Jun 22, 2012 2:22 pm Subject: Wiring harness routing for dimmer switch |
| I have a late M38 (May /52) am trying to determine correct routing of the 4 wires going to the headlight dimmer switch. Portions of the original harness was cut up and modified by PO and I am rebuildi ... |
| Topic: 24 Volt wires |
cross
Replies: 3
Views: 5996
|
Forum: Wanted Posted: Thu Feb 16, 2012 11:08 pm Subject: plug wires |
You may want to check these out
http://www.armysurpluswarehouse.com/m38-jeep-spark-plug-wire-set.html
Not sure what they are for but they do fit. |
| Topic: No pilot bearing in crankshaft |
cross
Replies: 4
Views: 5775
|
Forum: Technical Knowledge Base Posted: Fri Feb 03, 2012 12:55 pm Subject: I'm an idiot |
| Thanks guys, I'm a complete goofball and spaced out on this. Ive only replaced about 10 of these. |
| |
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
