Author |
Message |
Topic: Opinions needed |
heywood1
Replies: 6
Views: 7966
|
Forum: Technical Knowledge Base Posted: Wed Jan 14, 2015 9:08 am Subject: Opinions needed |
Skyjeep and allan
Both good points Ill think ill store the solid state one and keep on trucking
Alan ,the stencils came out great and the jeep is about finished.
Im waiting on some last parts (n ... |
Topic: Opinions needed |
heywood1
Replies: 6
Views: 7966
|
Forum: Technical Knowledge Base Posted: Wed Jan 14, 2015 7:08 am Subject: Opinions needed |
Point well taken |
Topic: Opinions needed |
heywood1
Replies: 6
Views: 7966
|
Forum: Technical Knowledge Base Posted: Tue Jan 13, 2015 8:11 pm Subject: Opinions needed |
I have a 1953 m38a1 i am putting the finishing touches on as a neighborhood regular driver.
I have the original voltage regulator that seems to be working fine and i have an NOS solid state voltage r ... |
Topic: Electrical adapter set manual needed |
heywood1
Replies: 2
Views: 4367
|
Forum: Technical Knowledge Base Posted: Sat Jan 03, 2015 9:46 am Subject: Electrical adapter set manual needed |
I have aquired a electrical adapter set for my m38a1 and m715
Part number 4910-348-7600
It did not have the manual to go with it
Does anyone have the manual for this test set
The correct manual i ... |
Topic: Correct siren for m38a1 |
heywood1
Replies: 1
Views: 4731
|
Forum: Technical Knowledge Base Posted: Sat Dec 27, 2014 7:51 pm Subject: Correct siren for m38a1 |
Does anyone have any info about which siren was correct for an m38a1 such as for a jeep assigned to an MP company.
Correct model,manufacturer any info would be appreciated. |
Topic: Ys carburetor rebuild question |
heywood1
Replies: 4
Views: 5976
|
Forum: Technical Knowledge Base Posted: Sat Dec 20, 2014 10:54 pm Subject: Ys carburetor rebuild question |
Ok will do
Thanks again |
Topic: Ys carburetor rebuild question |
heywood1
Replies: 4
Views: 5976
|
Forum: Technical Knowledge Base Posted: Sat Dec 20, 2014 10:46 pm Subject: Ys carburetor rebuild question |
Thanks wes,
That must be it . When I disassembled my carb that pin was not there and the metering rod was bent.
Im guessing you are correct,I'll finish the rebuild tomorrow thanks to your help. |
Topic: Ys carburetor rebuild question |
heywood1
Replies: 4
Views: 5976
|
Forum: Technical Knowledge Base Posted: Sat Dec 20, 2014 9:53 pm Subject: Ys carburetor rebuild question |
I am rebuilding my m38a1 ys carburetor and have hit a small snag.
All the parts in the kit make sense and match up with what i disassembled except one.
The kit has a really small pin about a half i ... |
Topic: Vacuum pump outlet |
heywood1
Replies: 6
Views: 8014
|
Forum: Technical Knowledge Base Posted: Sun May 18, 2014 8:48 pm Subject: Vacuum pump outlet |
Good point Wes,
I'm gonna have to get the tubing and the tee fitting,
That was gonna be my next concern,whether it would be ok to run it with the vacuum not hooked up to the distributor.
I'll try t ... |
Topic: Oil Pressure help...Please:( |
heywood1
Replies: 7
Views: 8270
|
Forum: Technical Knowledge Base Posted: Sun May 18, 2014 9:47 am Subject: Oil Pressure help...Please:( |
I once had a similar problem,had low oil pressure checked a dozen things ,decided to try a different oil wt .changed it from 30wt to 40wt oil and had good oil pressure for about 10 miles. After the en ... |
Topic: Vacuum pump outlet |
heywood1
Replies: 6
Views: 8014
|
Forum: Technical Knowledge Base Posted: Sun May 18, 2014 9:34 am Subject: Vacuum pump outlet |
Got it
thanks, |
Topic: Vacuum pump outlet |
heywood1
Replies: 6
Views: 8014
|
Forum: Technical Knowledge Base Posted: Sat May 17, 2014 8:08 pm Subject: Vacuum pump outlet |
Thank you for clearing that up but you still didn't answer my original question.
Can I operate with the suction port plugged without damaging any valves,diaphragm,etc? |
Topic: NO OIL PRESSURE |
heywood1
Replies: 20
Views: 24739
|
Forum: Technical Knowledge Base Posted: Sat May 17, 2014 6:05 pm Subject: NO OIL PRESSURE |
Had the same problem about 6 months ago.A motor I knew nothing about.
Started right up sounded great,zero oil pressure.
Dropped oil pan to check gallery plugs and oil pickup and everything looked fi ... |
Topic: Vacuum pump outlet |
heywood1
Replies: 6
Views: 8014
|
Forum: Technical Knowledge Base Posted: Sat May 17, 2014 5:49 pm Subject: Vacuum pump outlet |
I just rebuilt my original fuel/vacuum pump.Everything seems to be working fine but I need to know whether or not to plug the vacuum pump inlet.
I currently do not have a set of wipers nor do I have ... |
Topic: A question for the experts |
heywood1
Replies: 4
Views: 5618
|
Forum: Technical Knowledge Base Posted: Sun Jul 28, 2013 7:45 am Subject: A question for the experts |
I recently purchased a 1953 m38a1 project that was was about 3/4 of the way completed and the owner passed away before he could finish it.
It appears that he was doing a first class job,overhauled m ... |
|