Author |
Message |
Topic: correct float height m38a1 carb |
ktm25089
Replies: 6
Views: 6332
|
Forum: Technical Knowledge Base Posted: Mon Oct 08, 2018 1:51 pm Subject: correct float height m38a1 carb |
Hi again Wes,
im only asking about the correct float height,
yes i have read your papers and they have a lot of differences,
i see that the the 9/64" or 3,6mm is the correct height?is this OK?? |
Topic: correct float height m38a1 carb |
ktm25089
Replies: 6
Views: 6332
|
Forum: Technical Knowledge Base Posted: Mon Oct 08, 2018 1:17 am Subject: correct float height m38a1 carb |
Hello Wes
yes i have read the manuals a lot,and they helped me very much
in general your site is a jewel in information
i was asking because there is a lot of difference in float height for the sam ... |
Topic: correct float height m38a1 carb |
ktm25089
Replies: 6
Views: 6332
|
Forum: Technical Knowledge Base Posted: Sun Oct 07, 2018 2:57 pm Subject: correct float height m38a1 carb |
Hello,
just to cross check
correct float height for a m38a1 carburetor is 9/64" or 3,6mm???without gasket
and the m38 have 1/4" or 6,3mm
is this real so much difference?
thank you
George |
Topic: correct carb kit |
ktm25089
Replies: 1
Views: 3761
|
Forum: Technical Knowledge Base Posted: Thu Mar 22, 2018 3:01 pm Subject: correct carb kit |
Hello,
John at midwest is out of carb kits for my F-head.Any parts supplier that have CORRECT kit without smoking and rich idle?? |
Topic: convert to civil spark plugs and wires |
ktm25089
Replies: 3
Views: 6315
|
Forum: Technical Knowledge Base Posted: Sun Jun 18, 2017 9:16 am Subject: convert to civil spark plugs and wires |
i have fisished this conversion.The goal was to keep the distributor original and if i want to go back to military for a show etc to make it reversible quick.
so here are the proccess.
first you hav ... |
Topic: another one M38A1 carb problem please!!! |
ktm25089
Replies: 8
Views: 10954
|
Forum: Technical Knowledge Base Posted: Sat Jun 03, 2017 4:07 am Subject: another one M38A1 carb problem please!!! |
Thank you!!!!!! |
Topic: another one M38A1 carb problem please!!! |
ktm25089
Replies: 8
Views: 10954
|
Forum: Technical Knowledge Base Posted: Fri Jun 02, 2017 12:48 pm Subject: another one M38A1 carb problem please!!! |
the problem is that i dont have the old ones!!!!Thats the reason that im asking some measurements
And another one question.as the diaphragm goes back and pull the rod to the cap the mixture goes ric ... |
Topic: another one M38A1 carb problem please!!! |
ktm25089
Replies: 8
Views: 10954
|
Forum: Technical Knowledge Base Posted: Fri Jun 02, 2017 3:07 am Subject: another one M38A1 carb problem please!!! |
Wes,
All checked and it is OK.Do you have some dimension on the diapragm.I suspect that the see-through hole where the pin goes to attach the rod is on wrong height.
I have found more people have th ... |
Topic: another one M38A1 carb problem please!!! |
ktm25089
Replies: 8
Views: 10954
|
Forum: Technical Knowledge Base Posted: Thu Jun 01, 2017 11:13 am Subject: another one M38A1 carb problem please!!! |
Hello,
I have rebuild my carb.Soda-blasted,chemical and ultrasonic cleaned.repaired some threads with helicoil and installed a NAPCO 11-0578C japanese kit.The carb start and works very good.with the ... |
Topic: fuel gause adjust-correction |
ktm25089
Replies: 1
Views: 4259
|
Forum: Technical Knowledge Base Posted: Sun May 21, 2017 5:37 am Subject: fuel gause adjust-correction |
Hello,
i have installed an new fuel gauge (military stock) and new NOS fuel sender.installed an optional earth wire from gauge to sender.But the set is not working good.It never reads Full and never ... |
Topic: autolitte 2224 plug on F-134 |
ktm25089
Replies: 2
Views: 4733
|
Forum: Technical Knowledge Base Posted: Sun Apr 09, 2017 3:33 pm Subject: autolitte 2224 plug on F-134 |
Hello,
can we use the 2224 on f-134 engine?whats the differences with the 2245? |
Topic: M38A1 Wiper Vacuum Line Routing |
ktm25089
Replies: 9
Views: 24370
|
Forum: Technical Knowledge Base Posted: Sun Apr 09, 2017 2:51 pm Subject: M38A1 Wiper Vacuum Line Routing |
just rebuild my fuel pump fuel and vacuum.I have installed all the hoses,valves etc from one side of the vacuum that goes to the vavle cover and manifold.From the other side i just connected a hose an ... |
Topic: timing notch on pulley |
ktm25089
Replies: 1
Views: 4027
|
Forum: Technical Knowledge Base Posted: Mon Mar 27, 2017 3:20 pm Subject: timing notch on pulley |
Hello,
im trying to find the correct timing notch on my pulley.double military.Very close at where the original supposed to be there are 2-3 more hits and notches.I found that from the inside of the ... |
Topic: adjusting drag link m38a1 |
ktm25089
Replies: 13
Views: 17522
|
Forum: Technical Knowledge Base Posted: Wed Aug 17, 2016 12:53 pm Subject: adjusting drag link m38a1 |
Done!!!
Thanks all for the help!! |
Topic: adjusting drag link m38a1 |
ktm25089
Replies: 13
Views: 17522
|
Forum: Technical Knowledge Base Posted: Tue Aug 16, 2016 11:32 am Subject: adjusting drag link m38a1 |
ok,checked for the ends and the assembly of the parts.
after i will tight the bolts how much to loose them?
1/2 and 1/4 turn as 4x4m38 says?
thanks |
|