Author |
Message |
Topic: m38 distributer advance weights |
nepperjepper
Replies: 2
Views: 4195
|
Forum: Wanted Posted: Mon May 28, 2018 2:22 pm Subject: m38 distributer advance weights |
Thanks Wes
I knew My chances were slim of finding any. Mine are all wallered out. The MVPA convention is in a couple weeks and maybe I'll find some There..Jeff |
Topic: m38 distributer advance weights |
nepperjepper
Replies: 2
Views: 4195
|
Forum: Wanted Posted: Mon May 28, 2018 10:17 am Subject: m38 distributer advance weights |
Looking for a set of advance weights for the m38 or m38a1 24 volt distributer.
Thanks in advance Jeff |
Topic: spot welders |
nepperjepper
Replies: 4
Views: 5717
|
Forum: Technical Knowledge Base Posted: Wed Nov 17, 2010 1:23 pm Subject: spot welders |
The only experience I have with spot welders is with the 220v one from harbor freight. I went through 4 sets of tips and all the welds I made popped apart, I finally gave up and punched holes and plug ... |
Topic: Paper filter for M38 |
nepperjepper
Replies: 6
Views: 8644
|
Forum: Technical Knowledge Base Posted: Mon Nov 01, 2010 2:20 pm Subject: Paper filter for M38 |
WIX Filters Air Filter Element # 46230
Fram # ca3565
stp # af116 filter at autozone
Jeff |
Topic: Finally started working on my M38 |
nepperjepper
Replies: 310
Views: 342121
|
Forum: Jeep Project Threads Posted: Sat Oct 02, 2010 10:16 pm Subject: Finally started working on my M38 |
I thought about changing the plate also but I wasn’t up to taking the front of the newly rebuilt engine apart and trying to pull the gear off the camshaft can be a pain. Good luck with your project..J ... |
Topic: Finally started working on my M38 |
nepperjepper
Replies: 310
Views: 342121
|
Forum: Jeep Project Threads Posted: Sat Oct 02, 2010 9:56 am Subject: Finally started working on my M38 |
Yup same as mine, wrong mounting plate. Get the cut off wheel out..Jeff
http://willysmjeeps.com/v2/modules/gallery/albums/Nepperjepper-m38-s/IMG_0488.jpg |
Topic: M170 fuel system questions |
nepperjepper
Replies: 10
Views: 13243
|
Forum: Technical Knowledge Base Posted: Thu Sep 23, 2010 7:50 pm Subject: M170 fuel system questions |
I had the wrong engine mounting plate in mine also. Rather than change it I did some work with a cut off wheel and made it work…Jeff
http://willysmjeeps.com/v2/modules/gallery/albums/Nepperjepper-m ... |
Topic: fuel prime pump |
nepperjepper
Replies: 1
Views: 4314
|
Forum: Technical Knowledge Base Posted: Sat Sep 11, 2010 11:45 am Subject: fuel prime pump |
If you get a new old stock kit from one of the parts dealers it will have all the fitting, tubing and compression fitting with Ferrules. No flares required. It comes with two sizes of tubing 3/16 and ... |
Topic: m38 light switch help |
nepperjepper
Replies: 16
Views: 17617
|
Forum: Technical Knowledge Base Posted: Wed Jun 30, 2010 11:09 am Subject: m38 light switch help |
Next door neighbor. $&%, I wish he was my dad. Wes your not looking to adopt a 55 year old stepchild are you? I’ll bring my own jeeps. All you need to do is feed me and put me in the will. ha ha ha
... |
Topic: RUST |
nepperjepper
Replies: 4
Views: 7075
|
Forum: Technical Knowledge Base Posted: Mon Mar 15, 2010 6:25 pm Subject: RUST |
Hello weasel
I think you were talking to me, we bought a new old stock firewall and floor pan all in one piece and it had the hat channels already installed on the bottom, just like it came from the ... |
Topic: RUST |
nepperjepper
Replies: 4
Views: 7075
|
Forum: Technical Knowledge Base Posted: Sun Mar 14, 2010 5:49 pm Subject: RUST |
Has anyone else dealt with enough RUST to last them a lifetime. After about ten trips to the sand blaster… I have. Next time, a bigger air compressor and a blast cabinet.
http://willysmjeeps.com/v2/m ... |
Topic: S clip for Vacuum lines |
nepperjepper
Replies: 4
Views: 7110
|
Forum: Technical Knowledge Base Posted: Sat Jan 02, 2010 1:21 am Subject: 1/4" line clips |
You’re quite welcome.
I have been looking for the line clips on the windshield that holds the ¼” vacuum lines for the wipers.
Inline tube has some but the mounting holes are 3/8 and I think I need # ... |
Topic: Flywheel condition? |
nepperjepper
Replies: 3
Views: 5004
|
Forum: Technical Knowledge Base Posted: Fri Jan 01, 2010 12:14 pm Subject: ring gear flipping |
when i had my flywheel in for resurfacing. my machinist recommended to turn the ring over and have the new side of the gear facing the starter.Worked for me. the other half of the gear looked new.
... |
Topic: S clip for Vacuum lines |
nepperjepper
Replies: 4
Views: 7110
|
Forum: Technical Knowledge Base Posted: Fri Jan 01, 2010 11:54 am Subject: S clips |
This is where I Got Mine At.
http://www.inlinetube.com/ |
Topic: ab-449g antenna mount |
nepperjepper
Replies: 0
Views: 3276
|
Forum: Technical Knowledge Base Posted: Fri Oct 16, 2009 8:31 am Subject: ab-449g antenna mount |
Hello
I have been thinking about building a spare tire antenna mount (ab-449g) for my m38. I saw Cuz’s drawing in his photos page but I can’t read the dimensions on it. Can you please point me in the ... |
|