Author |
Message |
Topic: M38 Fuel shut-off valve brass connector at McMaster-Carr |
timber21
Replies: 5
Views: 4532
|
Forum: Technical Knowledge Base Posted: Sat Feb 09, 2019 3:06 pm Subject: M38 Fuel shut-off valve brass connector at McMaster-Carr |
Indeed, but could not find one, and the connector from McMaster does the job. |
Topic: M38 Fuel shut-off valve brass connector at McMaster-Carr |
timber21
Replies: 5
Views: 4532
|
Forum: Technical Knowledge Base Posted: Sat Feb 09, 2019 11:29 am Subject: M38 Fuel shut-off valve brass connector at McMaster-Carr |
Had a small leak at the fuel shut off valve caused by a hairline crack on the brass connector. Could not find it locally but located an almost identical part from McMaster-Carr, it is a typical autom ... |
Topic: Another Cause of Engine Overheating! |
timber21
Replies: 5
Views: 4777
|
Forum: Technical Knowledge Base Posted: Sun Oct 28, 2018 10:07 am Subject: Another Cause of Engine Overheating! |
I expected problems with the generator, but it passed all the field tests, so, I left it alone. It was one of those unintended projects that you think it would be done in a few hours and then when th ... |
Topic: Another Cause of Engine Overheating! |
timber21
Replies: 5
Views: 4777
|
Forum: Technical Knowledge Base Posted: Sun Oct 28, 2018 6:10 am Subject: Another Cause of Engine Overheating! |
Returning from a 50 mile trip, first heard belts squeaking momentarily and then noticed the voltmeter pegged out and temp was rising; took the next exit which was about a couple of miles down and the ... |
Topic: Another Cause of Engine Overheating! |
timber21
Replies: 5
Views: 4777
|
Forum: Technical Knowledge Base Posted: Sat Oct 27, 2018 5:57 pm Subject: Another Cause of Engine Overheating! |
http://willysmjeeps.com/v2/modules/gallery/albums/album616/regulator.sized.jpg[/img] |
Topic: M38 Steering Wobble |
timber21
Replies: 16
Views: 11824
|
Forum: Technical Knowledge Base Posted: Tue Sep 04, 2018 4:39 am Subject: M38 Steering Wobble |
Thanks again for all suggestions, support and recommendations.
Sincerely |
Topic: M38 Steering Wobble |
timber21
Replies: 16
Views: 11824
|
Forum: Technical Knowledge Base Posted: Mon Sep 03, 2018 4:47 am Subject: M38 Steering Wobble |
Thanks again, photos were corrected, will have to find the correct shaft and gasket to put it back together; and deal with the bell crank movement. |
Topic: M38 Steering Wobble |
timber21
Replies: 16
Views: 11824
|
Forum: Technical Knowledge Base Posted: Sun Sep 02, 2018 9:33 pm Subject: M38 Steering Wobble |
Thanks again, here are the photos, sorry, they are slightly over the size limit, will try to reduce them soon.
http://willysmjeeps.com/v2/modules/gallery/albums/album616/SteeringB.sized.jpg
http ... |
Topic: M38 Steering Wobble |
timber21
Replies: 16
Views: 11824
|
Forum: Technical Knowledge Base Posted: Sun Sep 02, 2018 7:37 pm Subject: M38 Steering Wobble |
Thanks again, will check the preload as soon as I find a fish scale. Do the photos have to be loaded from a photo gallery album or I could load them directly without having an album? I do not have on ... |
Topic: M38 Steering Wobble |
timber21
Replies: 16
Views: 11824
|
Forum: Technical Knowledge Base Posted: Sun Sep 02, 2018 3:53 pm Subject: M38 Steering Wobble |
Thanks for the response, king pin bearings are tight, with bell crank disconnected, no movement when the wheels are moved in and out vertically and/or horizontally, most of the slop has been in the be ... |
Topic: M38 Steering Wobble |
timber21
Replies: 16
Views: 11824
|
Forum: Technical Knowledge Base Posted: Sun Sep 02, 2018 11:33 am Subject: M38 Steering Wobble |
Thanks for the responses, it is the death wobble, it has been the issue since the unit was acquired, wheel bearings were replaced last winter; tie rods are fine. It starts acting up when going over a ... |
Topic: M38 Steering Wobble |
timber21
Replies: 16
Views: 11824
|
Forum: Technical Knowledge Base Posted: Sat Sep 01, 2018 3:08 pm Subject: M38 Steering Wobble |
Any comments/suggestions on the following issues are Greatly Appreciated, my apology if the issues have already been addressed, but I was unable to locate them; I searched the Forum and did not find t ... |
Topic: electrical |
timber21
Replies: 23
Views: 24784
|
Forum: Technical Knowledge Base Posted: Sat Dec 19, 2015 12:38 pm Subject: electrical |
Thanks for the info, on the regulator side there is continuity between pins A & C, however, there is a slight resistance between pins A & B or D. |
Topic: electrical |
timber21
Replies: 23
Views: 24784
|
Forum: Technical Knowledge Base Posted: Sat Dec 19, 2015 9:59 am Subject: electrical |
Using a hand-me-down wiring harness, the VR harness has only one wire (#4) coming out of the plug that is connected to pin A and in the middle of the cable a branch comes out that appear to be the #10 ... |
|