Create an account Home  ·  ·  Forums  ·  ·  Articles  ·  ·  Downloads  ·  ·  Photo Gallery  
Login
Nickname

Password

Don't have an account yet? You can create one here.

Navigation
· Home
· Article Archive
· Article Submit
· Downloads
· FAQ
· Forums
· Members List
· Photo Gallery
· Private Messages
· Web Links
· Your Account

Search Articles



Forums

M38 primer pump leather cups
Seat Belts
Happy Birthday Wes!
New Website tech needed
Trico Wiper Motor Disassembly Tool Name
Oil Pump Install
The 2017 Central Wisconsin MV Show
Top Bow bracket hole size...
Straightening Front Bumper Wings
R.I. Bong Veterans Center Military Vehicle Show

Willys M Jeeps Forums


willysmjeeps.com :: View topic - Body anti squeak locations
 Forum FAQForum FAQ   SearchSearch   UsergroupsUsergroups   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Body anti squeak locations

 
Post new topic   Reply to topic    willysmjeeps.com Forum Index -> Technical Knowledge Base
View previous topic :: View next topic  
Author Message
32sbct
Member


Joined: May 09, 2011
Posts: 132

PostPosted: Wed May 17, 2017 8:53 am    Post subject: Body anti squeak locations Reply with quote

Hello, I'll be mounting my body tomorrow. Where on the M38 body was the anti squeak webbing used. Every diagram I can find and the one that came with the kit is for an MB. In addition to the body cowl to fender location, does it also go between the fender and the step?

Does it go between the fender and grill? Any other locations? I can't find anything in ORD 9 except under section 1701-fenders.

Thanks,

Marty
Back to top
View user's profile Send private message
wesk
Site Administrator
Site Administrator


Joined: Apr 04, 2005
Posts: 12701
Location: Wisconsin

PostPosted: Wed May 17, 2017 9:09 am    Post subject: Reply with quote

In your M38 ORD 9 SNL G-740 dated 1955 look on page 341 which is the "A" page for the alphabetical index. They are the only places. Personally I would not use any of it. It absorbs moisture and stays wet long enough to start rust issues. There are many modern substitutes that do the job just fine. Go with rubbers, neoprene or teflon tapes and strips.

As I always say here: My album has hundreds of technical photos for the M38 & the M38A1. Visit it and use it. It is easy to find. It is the 2nd album on our "Members's Albums" page. http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php


This photo is in my M38 Body sub-album.
The long piece listed in the ord 9 goes vertical and the short piece goes horizontal.


This photo is in my "M38 Fuel System" sub-album.
_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100

Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php
Back to top
View user's profile Send private message Send e-mail Visit poster's website
wesk
Site Administrator
Site Administrator


Joined: Apr 04, 2005
Posts: 12701
Location: Wisconsin

PostPosted: Wed May 17, 2017 9:30 am    Post subject: Reply with quote

The key to proper, painless and accurate tub mounting is patience.

Do not tighten anything until you have test fitted all body parts (Tub, Fenders, Grill, Hood). It helps to have the engine mounted in the frame so you can insure proper alignment of the starter kick pedal with the starter. It takes a wee bit of tub mount tinkering to make them align.

Use my M38 "Body" album and the sub-album within "M38 Tub Mounting"!

http://www.willysmjeeps.com/v2/modules.php?set_albumName=album97&op=modload&name=gallery&file=index&include=view_album.php
_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100

Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php
Back to top
View user's profile Send private message Send e-mail Visit poster's website
32sbct
Member


Joined: May 09, 2011
Posts: 132

PostPosted: Wed May 17, 2017 11:34 am    Post subject: Reply with quote

Thanks Wes! I'll review all of those resources before I start.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    willysmjeeps.com Forum Index -> Technical Knowledge Base All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

Powered by phpBB © 2001 phpBB Group
Forums ©

 



PHP-Nuke Copyright © 2005 by Francisco Burzi. This is free software, and you may redistribute it under the GPL. PHP-Nuke comes with absolutely no warranty, for details, see the license.