View previous topic :: View next topic |
Author |
Message |
LTDan Member
Joined: Oct 13, 2017 Posts: 32
|
Posted: Wed May 16, 2018 1:51 pm Post subject: No oil to head, F134 (Solved) |
|
|
Hey once again guys,
I have a 1954 m38a1 with a 134f head motor.
Motor was freshly rebuild and new cam bearings installed. I have no oil coming to my head. Pulled the line and elbow, i am getting no oil flow from the passage.
I checked the passage below and i am getting oil flow there.
I was quite liberal with the engine assembly lube when i rebuilt the engine.
New cam bearings were also put in.
Is it possible that the lube has blocked the oil passage on the cam bearing?
Would motor flush help to clear it out?
or another possibility is to use one of the other oil passages and block off this passage?
I am getting 10 psi at idle and 20 psi at 2000 rpm cold.
With the engine hot it is producing 5 psi Idle and 20 psi at load.
Last edited by LTDan on Fri May 18, 2018 7:47 am; edited 1 time in total |
|
Back to top |
|
|
LTDan Member
Joined: Oct 13, 2017 Posts: 32
|
Posted: Wed May 16, 2018 6:46 pm Post subject: |
|
|
Well i'm figuring worst case scenario and i'm diving back into the block. Perhaps I have installed the rear main bearings incorrectly. |
|
Back to top |
|
|
Mike_B Member
Joined: Dec 10, 2017 Posts: 338 Location: Southern Maryland
|
Posted: Wed May 16, 2018 7:47 pm Post subject: |
|
|
Please correct me if I'm wrong, but isn't the head oiled via the cam bearings? Could one of the cam bearings be insatlled wrong blocking the oil passage?
Mike B _________________ Mike B
1953 M38A1 Brush Truck
1952 M38
1951 M100 Trailer |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16355 Location: Wisconsin
|
Posted: Wed May 16, 2018 9:45 pm Post subject: |
|
|
The f head valves and rocker are oiled from the #4 cam journal feed.
The F134 cam has 4 journals but uses only one bearing and it goes at the front #1 cam journal.
Many fresh Willys L & F 134 overhauls come out of the overhaul with low oil pressure. It is usually because we overlook two not so obvious places for wear beyond limits. The lifter bores and the #2 thru #4 cam journal block openings. There are oversize lifters that will allow you to solve a lifter bore wear issue but Willys decided not to support the back 3 cam journals with any bearings new or after field overhauls. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
LTDan Member
Joined: Oct 13, 2017 Posts: 32
|
Posted: Wed May 16, 2018 10:36 pm Post subject: |
|
|
So here is a thought wesk.
Would i be able to route from either the number 2 or 3 oil galley plug to the #4 cam journal, and route a line from either the number 2 or 3 passages up to my head?
I dropped the pan and the rear main bearing. Lower bearing is showing over heating and gouges in the surface, the crank shaft looks to be in good order still. As i cannot detect any marring on the surface of the crank shaft.
I am going to attempt to drop the crank tomorrow and inspect the upper bearing.
I am guessing that i have installed the rear main bearings wrong and have blocked the oil passage to the rear cam shaft journal. |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16355 Location: Wisconsin
|
|
Back to top |
|
|
LTDan Member
Joined: Oct 13, 2017 Posts: 32
|
Posted: Thu May 17, 2018 10:36 am Post subject: |
|
|
Your right wesk I was fighting the symptoms and not the problem.
I have pulled the engine out and am in the process of getting it torn down to inspect the main bearings. |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16355 Location: Wisconsin
|
Posted: Thu May 17, 2018 10:53 am Post subject: |
|
|
Keep in mind that 1/2 century old equipment is seldom in it's original state with all original parts. Carefully ensure that all your parts are correct for your engine. An early crank does not do well using a late rear main seal. An early block also does not do well using a late rear main seal. You cannot mix and match unless you machine both parts to the same spec. What is the casting number on your block? _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
LTDan Member
Joined: Oct 13, 2017 Posts: 32
|
Posted: Thu May 17, 2018 2:07 pm Post subject: |
|
|
The engine block casting number is 806279-W-12-D-AR |
|
Back to top |
|
|
LTDan Member
Joined: Oct 13, 2017 Posts: 32
|
Posted: Thu May 17, 2018 3:20 pm Post subject: |
|
|
I found it! I found the problem.
When the machinist had put in new freeze plugs he used a bit of Black RTV to provide a better seal. Well guess what was in the oil passage junction between the camshaft and the crank shaft.
Yep a little tiny plug of silicon.
I thought i had cleared all of the oil passages while washing the block. I have since learned to slow down and refer back to the manual on all of the basic systems of the engines operation.
|
|
Back to top |
|
|
Jason86 Member
Joined: Sep 19, 2015 Posts: 43 Location: Maine
|
Posted: Mon May 21, 2018 11:27 pm Post subject: |
|
|
Wes thank you for bringing up the subject about the block. I knew about the crankshaft needing to be remachined to spec to accept the neoprene seal from scanning other posts but I guess I overlooked the part about the block needing to also be redone which only makes sense but I figured the seals were manufactured to accept the rope style section of the block glad I caught that one before I send out my block. The picture in your album labeled (800093 Rear Main Seal 1) would that be the dimensions/print for the shop to go by to remachine the block to accept the new style seal?
I'll try to link the picture from your album..........[img]http://www.willysmjeeps.com/v2/modules.php?set_albumName=album134&id=G503_800093_Rear_Main_Seal_1_low_res_001&op=modload&name=gallery&file=index&include=view_photo.php[/img]
So are the later style blocks already machined to these dimensions?
I have not gotten to digging into my engine just yet so I do not know what style seals I have or if they have been converted but the 2 engines I have to choose from are block # 806279-W-13-D-AR are they early or late style?
Sorry LTDan to hijack your post but while on the subject I figured I'd ask, also good work on finding your problem.
As always thanks in advance. _________________ Jason
1953 M38A1 |
|
Back to top |
|
|
LTDan Member
Joined: Oct 13, 2017 Posts: 32
|
Posted: Tue May 22, 2018 9:26 am Post subject: |
|
|
Jason86 wrote: |
Sorry LTDan to hijack your post but while on the subject I figured I'd ask, also good work on finding your problem.
|
Its no problem bud, I am also talking with the machine shop now.
My crank had to be welded and machined on the rear main sealing surface.
I believe they left too much weld on the new surface and I ended up crushing my neopreen rear main seals.
I had the rope seals on hand in the kit so i used those before i ran into the no oil to head issue. |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16355 Location: Wisconsin
|
Posted: Tue May 22, 2018 10:34 am Post subject: |
|
|
I added more detail to the photo titles to answer your questions.
Keep in mind that the switch from rope seal to pre-formed seal did not happen during M38/M38A1/M170 production. If you have a MC, RMC, MD or RMD prefixed engine serial number your block left Willys set up for the pre-formed late seal. Your only worry would be weather the crank is original or an earlier substitute crank.
806279 is the later casting for the M38A1 and other Willys F134 applications. Your serial number ID's the original chassis installation. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
4x4M38 Member
Joined: May 30, 2014 Posts: 3459 Location: Texas Hill Country
|
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16355 Location: Wisconsin
|
|
Back to top |
|
|
|