Create an account Home  ·  ·  Forums  ·  ·  Articles  ·  ·  Downloads  ·  ·  Photo Gallery  
Login
Nickname

Password

Don't have an account yet? You can create one here.

Navigation
· Home
· Article Archive
· Article Submit
· Downloads
· FAQ
· Forums
· Members List
· Photo Gallery
· Private Messages
· Web Links
· Your Account

Search Articles



Forums

Photo Gallery Request
Expected co reading from L134 engine on M38
Design intent behind M38A1 battery box
M38 Generator Pulley Removal
M606/CJ3B WINDSHIELD FS; SWING OUT TYPE
Pilot bearing
Starter conversion
M38 A1 Carburettor screws
Warner T90 Transmission M38 gear shift housing removal
M38 Progress Hood installation

Willys M Jeeps Forums


willysmjeeps.com :: View topic - M38 Wiring Harness Transister Flash Turn Signal Unit Mount
 Forum FAQForum FAQ   SearchSearch   UsergroupsUsergroups   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

M38 Wiring Harness Transister Flash Turn Signal Unit Mount

 
Post new topic   Reply to topic    willysmjeeps.com Forum Index -> Technical Knowledge Base
View previous topic :: View next topic  
Author Message
rgmutchler
Member


Joined: Sep 28, 2008
Posts: 258
Location: Caldwell, Texas

PostPosted: Sun Apr 05, 2020 4:14 pm    Post subject: M38 Wiring Harness Transister Flash Turn Signal Unit Mount Reply with quote

I am working on my installing my wiring harness.
Where have others mounted the flasher unit for the turn indicators.
I thought i saw a picture on here someplace where it was mounted on the left side of the fire wall, outboard on the main wiring harness hole in the firewall and above the hole for the parking brake cable and the gas tank vent line hole.
I can't find that picture and from my playing with it it doesn't seem to fit very well there and so I am looking for suggestions, alternatives or that the place mentioned above is the only place.

Thanks,
Ralph
_________________
R G Mutchler
M274A5
M-38 MC13312
http://willysmjeeps.com/v2/modules.php?set_albumName=rgmutchler&op=modload&name=gallery&file=index&include=view_album.php
Back to top
View user's profile Send private message Send e-mail
wesk
Site Administrator
Site Administrator


Joined: Apr 04, 2005
Posts: 14857
Location: Wisconsin

PostPosted: Sun Apr 05, 2020 8:41 pm    Post subject: Reply with quote

Just go to my photo album, the 2nd album in the "Member's Albums" page and look at the sub-album, "Turn Signals". You should tell us which model Turn Signals you are installing.




The older relay system


The later kit only offers an instructions page.


Most folks mount the flasher unit from this late system to the back side of the firewall.
_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100

Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php
Back to top
View user's profile Send private message Send e-mail Visit poster's website
rgmutchler
Member


Joined: Sep 28, 2008
Posts: 258
Location: Caldwell, Texas

PostPosted: Sun Apr 05, 2020 9:34 pm    Post subject: Reply with quote

Wes,
I am still 24 v and am installing the later solid state unit or later style unit. I put some of that in the subject but used the word transistor instead of solid state, I should have put it in the body of the original message.

I had been through the turn signal album and saw where the old style was on the firewall in the engine compartment but didn't see any pictures of the newer solid state unit in the same place.
You said folks usually install the solid state unit on the "back side of the firewall." For my clarification, do you mean on the firewall in the engine compartment as I described above or on the firewall under the dash. I don't mean to be dense just wanted to make sure I understood.

Thanks
Ralph
_________________
R G Mutchler
M274A5
M-38 MC13312
http://willysmjeeps.com/v2/modules.php?set_albumName=rgmutchler&op=modload&name=gallery&file=index&include=view_album.php
Back to top
View user's profile Send private message Send e-mail
wesk
Site Administrator
Site Administrator


Joined: Apr 04, 2005
Posts: 14857
Location: Wisconsin

PostPosted: Sun Apr 05, 2020 11:19 pm    Post subject: Reply with quote

If you use the instruction sheet for the late transistor type it clearly states the choice of front or rear side of the firewall is up to you. (Front is side facing engine & the front of jeep and rear is side facing dash & the rear of jeep) As I said most folks keep the expensive electronic parts on the inside of the jeep not out under the hood.
_________________
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100

Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Rod
Member


Joined: Apr 19, 2005
Posts: 14
Location: Heart of Dixie

PostPosted: Tue Apr 14, 2020 6:22 pm    Post subject: Reply with quote

I am in the process of installing my wiring harness in the M38 and I will use the Solid state Turn signal controls from an M151. I will mount the controller on the inside of the firewall up and out of the way and line of sight.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    willysmjeeps.com Forum Index -> Technical Knowledge Base All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

Powered by phpBB © 2001 phpBB Group
Forums ©

 



PHP-Nuke Copyright © 2005 by Francisco Burzi. This is free software, and you may redistribute it under the GPL. PHP-Nuke comes with absolutely no warranty, for details, see the license.