View previous topic :: View next topic |
Author |
Message |
Mike_B Member
Joined: Dec 10, 2017 Posts: 337 Location: Southern Maryland
|
Posted: Wed Jan 31, 2018 4:43 pm Post subject: Carb is weeping gas at top cover screws |
|
|
So, my fresh carb is weeping gas at the top cover screws making the top cover wet with raw fuel. Is this a sign of the float set wrong? This happens overnight with the engine not running. I didn't put any gasket sealer on the paper gasket...should I have?
Thanks in advance,
Mike B _________________ Mike B
1953 M38A1 Brush Truck
1952 M38
1951 M100 Trailer |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
Posted: Wed Jan 31, 2018 5:30 pm Post subject: |
|
|
If the contact surfaces are in good shape you should never need to use a sealer on carb gaskets.
If you tell us which jeep your carb is on it will help with an answer.
I usually suggest to each of our members that you go to your profile page and add a signature element to all of your posts that includes at least your jeep's model number and your first name. Then the model of jeep referred to in your posts will always be obvious.
If you have an m38 then it is possible that you have forgotten the correct thick insulating gasket at the base of the carb to stop heat transfer from the intake/exhaust manifold which will cause perculation of the gas in the bowl after shut down.
If you have your bowl vent plugged this seaping can also happen. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules.php?set_albumName=Wes-Knettle&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
Mike_B Member
Joined: Dec 10, 2017 Posts: 337 Location: Southern Maryland
|
Posted: Wed Jan 31, 2018 6:33 pm Post subject: |
|
|
I fixed my signature...I had the info there but had double spaced it below my name and it didn't show...single spaced it and there it is! Thanks.
1953 M38A1...the carb is a YS-950.
It really looks like the gas is coming up the screw threads as the entire top is damp with fuel. _________________ Mike B
1953 M38A1 Brush Truck
1952 M38
1951 M100 Trailer |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
Mike_B Member
Joined: Dec 10, 2017 Posts: 337 Location: Southern Maryland
|
Posted: Wed Jan 31, 2018 10:54 pm Post subject: |
|
|
Thanks Wes, I'll look at both while I'm waiting for my starter motor to get rebuilt. _________________ Mike B
1953 M38A1 Brush Truck
1952 M38
1951 M100 Trailer |
|
Back to top |
|
|
Mike_B Member
Joined: Dec 10, 2017 Posts: 337 Location: Southern Maryland
|
Posted: Thu Feb 08, 2018 9:01 am Post subject: |
|
|
Ok, so I checked the vent and it's clear, it's piped from the top of the carb to the air intake as shown on page 70 ORD-9 SNL G-758.
I took the top of the carb off and adjusted the float again using a 1/4" drill bit as a gauge. Ran the engine for 30 min and called it good. Came out the next day and the top of the carb is all wet again. This time I noticed the carb intake right at the choke plate was wet with raw gas, but not the section of pipe the vent is connected to.
My question is when adjusting the float do you push down on the needle seat valve spring to set the height or not? I'm wondering if there isn't enough spring pressure to overcome the pump pressure. This is the first carb I've done that hase a spring at the needle valve.
I'll check the pump pressure later today, but since the pumps been there for 30 years I find it hard to believe it's putting out to much pressure.
Thoughts?
Thanks,
Mike B _________________ Mike B
1953 M38A1 Brush Truck
1952 M38
1951 M100 Trailer |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
Mike_B Member
Joined: Dec 10, 2017 Posts: 337 Location: Southern Maryland
|
Posted: Tue Feb 13, 2018 2:38 pm Post subject: |
|
|
Thanks Wes, that's the way I have it set.
I believe the problem was I had the temporary fuel tank attached to the top of the grille guard which had it higher than the top of the carb allowing it to siphon into the bowl overnight. I lowered the tank and the problem went away. For some reason the needle seat must not close off 100% allowing a small amount of gas to seep by...this condition would not happen normally as the tanks below the carb.
Mike B _________________ Mike B
1953 M38A1 Brush Truck
1952 M38
1951 M100 Trailer |
|
Back to top |
|
|
|