View previous topic :: View next topic |
Author |
Message |
TGP Member
Joined: Jan 05, 2016 Posts: 41 Location: Southern, IL
|
Posted: Thu Mar 24, 2016 10:49 am Post subject: Top Bows M38A1 |
|
|
Ok little help here.
I have MWM top bows and rods.
WeeBee Webbings drawing shows a 27.5" vertical rod and
According to there Pic's the vertical rod is flush with the
Top Horizontal rod.
Johns are 29" and according to pic's on Wes's albums of other
Jeeps the extra length passes above the top rod a few inches.
Should I cut??
Also not sure how John's vertical to horizontal clips orientate.
Have some idea but does the vert. rod pass to the inside of the
Horz. rod? That's how I interpret the few pic's I see.
Is the clamp screw on top or bottom and clamps the Vertical rod?
Or clamps the Horizontal rod and the Vertical rod floats.
The bottom body rod holder that the rod sits in is capped, so it
Can't fall through.
Hoping someone can help I hate to bother John unless I have too.
Thanks
Tom _________________ "86" M1028A2 Dually
"65" M35A1 WW
"54" M38A1
"52" M37 WW
"47" WDX WW
My Album
http://www.willysmjeeps.com/v2/modules.php?set_albumName=album471&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
4x4M38 Member
Joined: May 30, 2014 Posts: 3447 Location: Texas Hill Country
|
|
Back to top |
|
|
TGP Member
Joined: Jan 05, 2016 Posts: 41 Location: Southern, IL
|
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
4x4M38 Member
Joined: May 30, 2014 Posts: 3447 Location: Texas Hill Country
|
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
4x4M38 Member
Joined: May 30, 2014 Posts: 3447 Location: Texas Hill Country
|
|
Back to top |
|
|
TGP Member
Joined: Jan 05, 2016 Posts: 41 Location: Southern, IL
|
Posted: Thu Mar 24, 2016 1:43 pm Post subject: |
|
|
Thanks Wesk.
I saw the drawing but it's in two pages .
Now that you posted them together and more importantly
I found that you double click to enlarge even more I understand it now.
If I'm looking at this right the connector in circle "K" points the
Vertical rod to the outside of the Horizontal rod?
Thought I saw other pictures with the vert. rod to the inside?
Sorry for posting in wrong forum I wasn't sure if I was to pull
up my old build thread or start new in the project forum.
Obviously it belongs in Technical forum.
Tom _________________ "86" M1028A2 Dually
"65" M35A1 WW
"54" M38A1
"52" M37 WW
"47" WDX WW
My Album
http://www.willysmjeeps.com/v2/modules.php?set_albumName=album471&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
TGP Member
Joined: Jan 05, 2016 Posts: 41 Location: Southern, IL
|
Posted: Thu Mar 24, 2016 3:43 pm Post subject: |
|
|
wesk wrote: | I suspect a technical writer error there. If you leave the sharp edge of the clamp outboard it will saw through the canvas.
Also note that this clamp allows for adjusting the vertical rod relative to the door frame. |
That's exactly what I was thinking.
Well I got the top on and very pleased.
Pictures later in my album after I get them loaded.
Thanks.
TGP _________________ "86" M1028A2 Dually
"65" M35A1 WW
"54" M38A1
"52" M37 WW
"47" WDX WW
My Album
http://www.willysmjeeps.com/v2/modules.php?set_albumName=album471&op=modload&name=gallery&file=index&include=view_album.php |
|
Back to top |
|
|
TGP Member
Joined: Jan 05, 2016 Posts: 41 Location: Southern, IL
|
|
Back to top |
|
|
|