Guys'
Thanks for all the advice. MC60976, while out of time, starts and holds idle. The stripped stud was replaced with a threaded insert and the mashed head gasket is no more!!! I stopped working on her for the night, I am too excited and do not want to rush anything tonight.
Wes and Ryan thanks a million or $3K however you look at it. Now that she runs I can really spend some dough!! Thank You to everyone who keeps willysmjeeps.com up and running. This is a great site and you do a great job.
Thanks again,
Scott
MC60976 3/52 IS ALIVE
- Scott21
- Active Member

- Posts: 232
- Joined: Wed Apr 11, 2007 6:00 pm
- Location: Central New Jersey
- wesk
- Site Administrator

- Posts: 16471
- Joined: Sun Apr 03, 2005 6:00 pm
- Location: Wisconsin
- Contact:
Hello Scott,
It is sweet music to the ears isn't it?
It is sweet music to the ears isn't it?
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules. ... _album.php
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules. ... _album.php
- Scott21
- Active Member

- Posts: 232
- Joined: Wed Apr 11, 2007 6:00 pm
- Location: Central New Jersey
- GIJOE290
- Jeep Enthusiast

- Posts: 269
- Joined: Tue Apr 12, 2005 6:00 pm
- Location: Altamonte Sprgs, FL 32714
- Contact:
- wesk
- Site Administrator

- Posts: 16471
- Joined: Sun Apr 03, 2005 6:00 pm
- Location: Wisconsin
- Contact:
If the idle is smooth and the cruise RPM smooth and steady but it stumbles when you quickly advance the throttle then either you have a malfunction with the accelerator pump or your idle mixture is to lean. You haven't told us which carb you are using and it's status, IE recently overhauled or very used etc.
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules. ... _album.php
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules. ... _album.php
- wesk
- Site Administrator

- Posts: 16471
- Joined: Sun Apr 03, 2005 6:00 pm
- Location: Wisconsin
- Contact:
Then most likely the accelerator pump is not adjusted correctly, or it's linkage is broken/not connected, or it's seal disc on it's plunger is bad.
With the engine NOT running and the metal horn cover removed from the top of the carb and the choke flapper wide open you can look into the bore of the carb, then manualy move the accelerator linkage from the idle stop to wide open position and you should observe a steady stream of raw gas squirting into the bore as the linkage is moved.
With the engine NOT running and the metal horn cover removed from the top of the carb and the choke flapper wide open you can look into the bore of the carb, then manualy move the accelerator linkage from the idle stop to wide open position and you should observe a steady stream of raw gas squirting into the bore as the linkage is moved.
Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules. ... _album.php
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Mjeeps photo album: http://www.willysmjeeps.com/v2/modules. ... _album.php
- Ryan_Miller
- Site Administrator

- Posts: 1686
- Joined: Sat Apr 02, 2005 6:00 pm
- Location: Kansas
