View previous topic :: View next topic |
Author |
Message |
Cacti_Ken Member
Joined: Apr 20, 2005 Posts: 1021 Location: Silsbee, Texas
|
Posted: Thu Nov 09, 2006 10:27 pm Post subject: Rubber pad |
|
|
Was the pad under the grill BO marker light a thick O'ring? Page 161, part # 7375023.
I also notice in the parts list a pad for the head light Part # 7375022. What is it talking about? _________________ Tropical Veteran
35th Inf. Reg. "CACTI" 4th I.D. VN
Amateur Radio K5XOM |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
Cacti_Ken Member
Joined: Apr 20, 2005 Posts: 1021 Location: Silsbee, Texas
|
Posted: Thu Nov 09, 2006 11:48 pm Post subject: |
|
|
Ok good then I can make me some, but don't understand the one it calls for on the head light. _________________ Tropical Veteran
35th Inf. Reg. "CACTI" 4th I.D. VN
Amateur Radio K5XOM |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
kenperkins Member
Joined: Apr 14, 2005 Posts: 285 Location: Livermore Ca.
|
Posted: Fri Nov 10, 2006 7:03 pm Post subject: |
|
|
7375024 is the head light gasket
look at the blow up of the marker light in the ORD 9... if the pad 7375023 is not thick the light will not be centered in the grill cut out (verticaly)I don't have it on mine and the light sits about 3/8 lower than centered.
if your using all the right gaskets and pads under your lights don't forget 7346941 |
|
Back to top |
|
|
Cacti_Ken Member
Joined: Apr 20, 2005 Posts: 1021 Location: Silsbee, Texas
|
Posted: Fri Nov 10, 2006 8:52 pm Post subject: |
|
|
I have the two headlight bucket gaskets which go between the HL bucket and the grill. I found a couple of rubber grommets that could be used for the pad for the grill marker BO lites. Except they are about 1/2 tall. I cut it down to about 3/16" which just about centers the fixture.
Sometime's, (in my opinion the Ord 9 isn't clear) and have a little trouble in deciphering it. _________________ Tropical Veteran
35th Inf. Reg. "CACTI" 4th I.D. VN
Amateur Radio K5XOM |
|
Back to top |
|
|
wesk Site Administrator
Joined: Apr 04, 2005 Posts: 16256 Location: Wisconsin
|
|
Back to top |
|
|
Cacti_Ken Member
Joined: Apr 20, 2005 Posts: 1021 Location: Silsbee, Texas
|
Posted: Sat Nov 11, 2006 11:22 am Post subject: |
|
|
The head light and BO driving light don't show a rubber pad in the pictures. Yet gives a part number for them. Ho Hum!
Wes, thanks I'll see what I can come up with here before requesting an order from you.
Ken _________________ Tropical Veteran
35th Inf. Reg. "CACTI" 4th I.D. VN
Amateur Radio K5XOM |
|
Back to top |
|
|
OKCM38CDN Guest
|
Posted: Sat Nov 11, 2006 7:07 pm Post subject: |
|
|
Ken,
I went to ACE today for some other hardware and I found they have Rubber washers up to 2" in diameter and 1/8" thick with a 3/8" hole in the center just what you need... they were $1.11 ea... In the little parts boxes is where I found them... They come in smaller sizes also...
Hope this helps... |
|
Back to top |
|
|
Cacti_Ken Member
Joined: Apr 20, 2005 Posts: 1021 Location: Silsbee, Texas
|
Posted: Sat Nov 11, 2006 9:07 pm Post subject: |
|
|
Thanks Hal, I have picked up some of those. _________________ Tropical Veteran
35th Inf. Reg. "CACTI" 4th I.D. VN
Amateur Radio K5XOM |
|
Back to top |
|
|
|