Tearing engine down for a shake a bake, plus mag. Gotten most of it apart. The left oil passage block, on the Oil pump side of the block (Not the one the throttle spring hooks to) is stuck. I have tried pb, and heat. The wrenches have started to round the head a bit. I stopped once i saw the rounding starting. I am completely stumped, how do you remove one of these seized up plugs ?
Another issue is when i took my head off and looked inside the water jacket, i saw and felt a piece of metal in there. It is right in the middle of the head's jacket. It runs about two piston length, and is rounded on the ends. It looks like a metal strap that was in there and corroded off. Any ideas as to what it is ? should i be worried, or ehh, Doesn't seem to impede flow, but it is loos in there, but too big to block any passages. Tried removing it, but too hard and long to bend to get out.
Last but not least a broken drill bit question. Took my water pump off, and saw one of the bolts had been broken off in the block (been there a while i see). So tried to drill and easy out it, broke easy out in stud, then i drilled the easy out and a bit of the stud. WellL the drill bit broke off in the stud, any ideas how to get hardened drill bit out ? I had heard a rotozip carbon blade would grind/drill it out, the ones used for tile. Any ideas there ?
Joined: Feb 17, 2012 Posts: 530 Location: Del City, OK
Posted: Mon Jul 11, 2016 7:31 pm Post subject:
I broke a tap off in one of the Axle holes for the differential cover, I asked a machinist what to do to get the tap out. His answer was a carbide Dremel tool bit, at a low speed cut the tap out slowly. He said was only way unless I wanted to bring the axle to him... it is mounted and would be a big pain in the butt to go this route.
So maybe try this... _________________ Hal, KB1ZQ
TSGT, USAF (Ret)
1952 M-38 CDN CAR 52-31313
1952 M-100 Strick #104
1951 Willys Wagon (For Sale)
1954 Willys M38A1 201001205
Tornado Alley
Del City, OK
Joined: Jun 07, 2010 Posts: 69 Location: Maryhill On
Posted: Tue Jul 12, 2016 6:36 am Post subject:
The wire in the water jacket is probably part of the core reinforcement. It stays in the engine when the casting process is finished and the core sand is broken out.
Haven't seen one in a F134 though. Take it out and send us a picture. _________________ M38 CDN 52-30105
M38 CDN 52-30883
I've been through all the methods of removing a broken bolt or stud, especially from a block. Easy/outs, taps, pliers, etc. Etc. Etc. There is one way that works every time. So once you've tried everything else.....
Find a nut thats slightly bigger than the bolt or plug that's stuck. Hold it over top of the bolt so you can see the bolt thru the nut. Weld the inside of the nut to the bolt. If it's broken so it's hard to reach just build up the weld a bit more. Low heat, and don't go crazy with the welding.
This process does a few things. It heats up the rust that is holding the bolt. It heat/cycles the bolt and It'll likely break the bolt loose. And lastly it gives you a nice big brand new nut for your socket wrench. Works everytime.
the quick center tools work on bolts below the surface. I had a hub bolt broken off about an inch below the surface nd the tool worked flawlessly _________________ Gary Keating
1949 C3A, 1952 M38,
1954 M170, 1957 Cj3B
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum