Joined: Oct 02, 2014 Posts: 1918 Location: South Carolina, Dorchester County
Posted: Tue May 23, 2017 8:55 pm Post subject: M38 Late Firewall Question - Unused Hole Cover Plates
My M38 has a late firewall. In Ryan Miller's M38 Reference Guide on page 141, the late firewall photo shows find number 25 is three unused holes for cables that are supposed to have covers on them when not used. I'm not using them so I need covers.
Looking at the ORD9 for Group 1805 on page 300, there are two different PLATE, DASH PANEL CABLE OPENING (used on vehicles after serial number 35387):
1 each, G740-7418148, WO-677712
1 each, G740-7697582, WO 674428
Are these the firewall hole covers? I could be way off track as there's only one of each part number and there are 3 holes (the same size). I haven't located any other likely candidates in the ORD9 and haven't been able to find any thing else searching, including dimensions.
Can anybody confirm the correct part numbers for these 3 hole cover plates on the firewall? Shape and dimensions for fabrication? Any source for NOS or otherwise?
As always, your advice is appreciated. _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
Late firewall
Note the two heater hose holes 6 & 7 appear to be different sizes. The third hole that has two screw holes for a cover plate is 21. Have you measured the distance between the cover plate attach screw holes on all three?
Early firewall for reference. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Joined: May 30, 2014 Posts: 3447 Location: Texas Hill Country
Posted: Wed May 24, 2017 6:25 am Post subject:
Early firewall, version 2.
So it looks like hole 8 in the below early photo became hole 21 in the later
photo ( our numbers I know). They just blanked the hole with that plate.
Wes, I'm assuming the later vehicles came with the heater holes drilled
and plated over. Heater was installed in the field as needed?
Ron, you can easily make those plates. I'm betting they are 18 gauge
but if you have 16 on the bench it would work. Someone here may be
able to trace theirs and get you a drawing. You can probably find them
but I'm guessing for what some folks want for them you can use that
money elsewhere.
Joined: Oct 02, 2014 Posts: 1918 Location: South Carolina, Dorchester County
Posted: Wed May 24, 2017 7:45 am Post subject:
Wes,
Using your late model photo is some progress!
I haven't measured anything yet to confirm. While holes 6 and 7 are different sizes, the screw holes to fasten the covers look to be spaced the same which makes me think the same size cover works on both holes? Why make two different size covers when one size fits all? Your photo also gives me the shape of the cover. I was wondering if it was round, round with tabs for screws, or oval as your photo shows.
The third hole (#14 in your photo) also has screw hole spacing similar to the other two that makes me think one size cover works on all three holes. The only problem with my thinking is I can't get the ORD9 part numbers to line up with it.
I'd rather buy take-off's or NOS covers if I can find some. Brian, I agree that fabricating wouldn't be hard, but it's usually my last resort.
Thank you! _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
my thinking is I can't get the ORD9 part numbers to line up with it.
That happens sometimes in the parts manual for extremely minor importance parts or sub-assemblies. The only place you can be sure to properly ID them is on the Willys blue print for the firewall.
Quote:
The third hole (#14 in your photo)
That would be the 4th hole for this discussion! I had already addressed 6, 7, & 21
Joined: Oct 02, 2014 Posts: 1918 Location: South Carolina, Dorchester County
Posted: Wed May 24, 2017 8:31 am Post subject:
Hi Wes,
The late model firewall photo in Ryan's M38 Reference Guide is a little confusing because it has two #25's pointing at two holes on the left side of the photo and one hole on the right. His #25's (three of them) correspond to hole #'s 6, 7, and 14 in your late model photo. I wasn't asking about your photo hole #21, although now I need to go back and look at that one too just to be sure, but I think it's used.
Thanks again, I'm pointed in the right direction. _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
It would be best to use the hole #'s we have in this post and ignore the numbers in Ryan's book.
My 21 is Ryan's 11. I try to offer up body hole indexes that show the actual use for each hole. _________________ Wes K
45 MB, 51 M38, 54 M37, 66 M101A1, 60 CJ5, 76 DJ5D, 47Bantam T3-C & 5? M100
Joined: Oct 02, 2014 Posts: 1918 Location: South Carolina, Dorchester County
Posted: Wed May 24, 2017 9:20 am Post subject:
10-4. I was just pointing out the source of my confusion, which is not uncommon. _________________ Ron D.
1951 M38 Unknown Serial Number
1951 M100 Dunbar Kapple 01169903 dod 5-51
“The only good sports car that America ever made was the Jeep."
--- Enzo Ferrari
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum