Page 1 of 1
M38 Body Hole Location
Posted: Wed Jun 13, 2012 11:58 pm
by Rotorhead
I've got a 52 M38 with a newer body - the previous owner threw out the old one for scrap and did not reinstall all of the military gear. The newer body has no holes for things like footman loops, canopy bow brackets, pioneer kit, etc. Are there drawings available with measurements for drilling these holes? I've got lots of pics, but I'd like to be as precise as possible. Thanks a bunch!!!
Posted: Thu Jun 14, 2012 12:41 am
by evanso1975
Check out this photo, courtesy of Wes:
http://www.willysmjeeps.com/v2/modules. ... _photo.php
Also, there's lots of great photos in Wes's "M38 Body" album here:
http://www.willysmjeeps.com/v2/modules. ... php&page=1
A big thank you to Wes for providing all this information to get us jeep restorers out of the trouble we invariably find ourselves in!
Owen.
Rear Bench Seat Provisions
Posted: Thu Jun 14, 2012 11:43 am
by Rotorhead
Wow!!! That is great info - thank you so much. I'm grinnin' ear-to-ear. And great job, Wes! Does anyone have measurements to locate the rear bench provisions (spring, support bracket, etc)? I found an original seat and all of the original brackets, recovered the seat with new foam and canvas, and I'm now about to install the provisions, but would like to get it spot-on.
Posted: Thu Jun 14, 2012 7:01 pm
by wesk
I have one somewhere. Will look around.
M38 Rear Bench Bracket Location
Posted: Tue Jun 19, 2012 10:03 am
by Rotorhead
I hope to install the provision this weekend for the rear bench seat. Anyone have measurements for the pivot bracket, perhaps from the floor up and from the tail gate forward? New tires today, and new suspension tomorrow!!!
Posted: Tue Jun 19, 2012 1:03 pm
by wesk
M38 Rear Bench FP Location
Posted: Wed Jun 20, 2012 1:26 pm
by Rotorhead
Wow! Thank you again, Wes!! That's perfect. Do you also have the same for the pioneer kit brackets? I have your pic of the right rear quarter and the pioneer kit brackets are there but no dims.
Posted: Wed Jun 20, 2012 4:40 pm
by evanso1975
Sorry to hijack Rotorhead's post, but does anyone have the diameter of the big hole that the top bow wing bolt goes through?
Btw. that's the one shown as being 14-3/4" from the back panel in Wes's photo.
Thanks in advance,
Owen.
Posted: Thu Aug 16, 2012 1:35 pm
by evanso1975
Bump!
Sorry to hijack Rotorhead's post, but does anyone have the diameter of the big hole that the top bow wing bolt goes through?
Btw. that's the one shown as being 14-3/4" from the back panel in Wes's photo.
Thanks in advance,
Owen.
Anyone know that hole size?
Posted: Thu Aug 16, 2012 1:43 pm
by RICKG
evanso1975 wrote:Bump!
Sorry to hijack Rotorhead's post, but does anyone have the diameter of the big hole that the top bow wing bolt goes through?
Btw. that's the one shown as being 14-3/4" from the back panel in Wes's photo.
Thanks in advance,
Owen.
Anyone know that hole size?
1-1/8".
Posted: Thu Aug 16, 2012 1:49 pm
by evanso1975
Thanks Rick!
Posted: Thu Aug 16, 2012 7:48 pm
by xheadnut
I bought a template from one of the MV dealers a couple of years ago, but I can't remember which one
Posted: Fri Aug 17, 2012 12:13 am
by evanso1975
I bought a template from one of the MV dealers a couple of years ago, but I can't remember which one
Thanks for the tip.
I see Beachwood Canvas do one for the bracket & footman fixing holes:
https://www.beachwoodcanvas.com/order/p ... TMP&line=3
The large hole for the wing bolt isn't shown, but I guess you can work out the position by fitting the top bow bracket and marking though the centre hole.
Owen.
