Page 1 of 2
Generator to regulator cable
Posted: Sun May 28, 2006 2:16 pm
by Cacti_Ken
This generator cable that came with my harness measures 36 inches and has a 90 degree connector on the regulator end.
Do you think that it is correct for the M38.
When I have it connected to the Generator and regulator I have a loop of cable that hangs down near the drive shaft.
Is that the way it is supposed to go?
How does your cable fit?
Posted: Sun May 28, 2006 3:34 pm
by Ryan_Miller
Ken,
The cable should be straight on both ends.
I'll look up the length.
Posted: Sun May 28, 2006 7:43 pm
by Cacti_Ken
It's about 20 inches too long if the 90 degree end is used. It's also about one inch in diameter.
Posted: Mon May 29, 2006 6:44 am
by remi_emond
is the cable for sale?
Remi
Posted: Mon May 29, 2006 1:07 pm
by Cacti_Ken
It isn't for sale at the moment. It is the only cable I have that goes from generator to regulator. The ends will connect, but I have a lot of slack in the cable. So until I get the proper one I will keep this one. I have to call the person that sold it to me.
Anyone have a photo of yours installed?
Posted: Tue May 30, 2006 12:52 pm
by Cacti_Ken
Well I called the vendor that sold me the harness and cables. He said I was the first in 18 yrs to bring up this question. And as far as he knows it is the correct cable. I don't think it should fit this way. I can make it fit either on top or let the loop hang down on the bottom underneath.
Posted: Tue May 30, 2006 6:28 pm
by Ryan_Miller
Ken,
The cable should be straight on both ends.
I find it hard to believe that this vendor has never had a person question this item before!
I measured mine to be about 35 1/2 to 36 inches long.
Posted: Tue May 30, 2006 8:19 pm
by Cacti_Ken
Ok Ryan thanks, I gotta find the right cable.
Posted: Tue May 30, 2006 9:16 pm
by Jeff_H
here is what it looks like on my M38. The "loop" is just behind the tub brace thingy (what the heck is that actually called anyway?).
Jeff
Posted: Tue May 30, 2006 10:27 pm
by wesk
That looks like the early 51 and 50 fat boy cable. The metal support is called the "toeboard Gusset".
Here's what I wrote on the 503 about this:
The very early cable assembly was a Titeflex unit PNB37559 (WO PN 801191 & ORD PN 776732).
The later cable assembly was a Titeflex unit PN B36834 (ORD PN 7539500) .
None of the parts books specify when the switch took place but odds are it was shortly after August 1951.
The only difference I have noticed is the shielded sleeve asembly composition and diameter. Both have straight ends on each end. My 1952 unit 24.5" tip of connector to tip of connector. The rubber coated shield sleeve has "Titeflex Type 159A" on it.
Both have ORD stock number prefixes of G742 (REO 2 1/2T 6x6).
My late 52 cable.
This is what I believe to be the correct early cable assembly.
Posted: Wed May 31, 2006 9:20 am
by Cacti_Ken
Jeff, where did you purchase your cable?
Posted: Wed May 31, 2006 12:30 pm
by Jeff_H
Cacti_Ken wrote:Jeff, where did you purchase your cable?
Ken
Sorry can't help, it came with the jeep!
Jeff
Posted: Wed May 31, 2006 2:47 pm
by Bill_F
I have a spare cable but you are going to have to wait until the end of august to get it.
Posted: Wed May 31, 2006 3:50 pm
by Cacti_Ken
Bill, Referring to Wes's photos, Do you have the early or late cable?
Ken
Posted: Wed May 31, 2006 4:41 pm
by Bob_C
Ken,
Did you try Star Electric? They might have it.