m100 trailer

circleburner12 · Post by **circleburner12** » Fri Apr 12, 2013 7:20 pm

im starting my restore on my m100 trailer next week! finally got the end and floor panels in after a long wait.

so im looking for do's and dont's while restoring this trailer. so if anyone would give me some info on restoring a m100 trailer that has restore one and learn some do's and dont's, i'll take any info that your willing to share. thxs

Post by **wesk** » Fri Apr 12, 2013 9:53 pm

It helps to have the manuals.

TM 9-871A Operator & Maintenance July 1951
ORD 9 SNL G-747 February 1952
ORD 7 & 8 SNL G-747 July 1956
TM 9-2330-201-14 Operation, Maintenance & parts April 1972

http://www.ih8mud.com/tech/pdf/trailer/m100-m115.pdf

The WWII trailer manuals and the M416 manuals are helpful for comparing parts interchangeability.

Do you have data plates with your trailer and did it come with the early or late type trailer to jeep cable and the cable storage box?

circleburner12 · Post by **circleburner12** » Sat Apr 13, 2013 11:35 am

data plates are there, no storage box but the brackets are there. no cables,

ive been storing it at my parents house and moved it to my brothers welding shop yesterday. but if i remember right it seems the date of the trailer was 1953.

Post by **wesk** » Sat Apr 13, 2013 11:45 am

The first couple of years the trailer came with a receptacle in the lower right (pass side) front corner for one end of the intervehicle cable. Later trailers did not have this receptacle. Instead the tail light wires ran all the way up inside the right diagonal drawbar to a terminal arrangement where the newer single ended intervehicle cable was attached via those Douglass connectors. This area of the right diagonal drawbar had a plate bolted on to cover the terminals and the cable storage box was dropped but the two brackets remained.

circleburner12 · Post by **circleburner12** » Sat Apr 13, 2013 3:49 pm

yes it does have the bracket in place for the receptacle in the lower right (pass side) front corner for one end of the intervehicle cable.

circleburner12 · Post by **circleburner12** » Sat Apr 13, 2013 7:08 pm

as far as restoring the tub, which the floor is all but gone due to rust. should I start with replacing the floor or start replacing the end panels? if anyone has pics of there trailer while restoring could you be so kid and post them or send to my pm box. thxs

donthedickens · Post by **donthedickens** » Tue Apr 23, 2013 6:34 am

circleburner12 wrote:im starting my restore on my m100 trailer next week! finally got the end and floor panels in after a long wait.

so im looking for do's and dont's while restoring this trailer. so if anyone would give me some info on restoring a m100 trailer that has restore one and learn some do's and dont's, i'll take any info that your willing to share. thxs

==================

Where did you get your end and floor panels?

Can you post some pictures of what you received?

circleburner12 · Post by **circleburner12** » Fri Apr 26, 2013 9:21 am

i purchase the panels from stephen greene. greene's panel works. he went out of business and says he has some panel's in stock.

BUT! before you contact him and see if he has anymore in stock and purchase panels from him, you need to contact me, because you will change your mind. thxs

donthedickens · Post by **donthedickens** » Fri Apr 26, 2013 9:44 am

I sent you a PM.

Thanks

willysmjeeps.com

m100 trailer

m100 trailer

Re: m100 trailer